manualshive.com logo in svg

Diamond Tools ICS 701-A Series, Руководство оператора

Поделиться
Скачать
Diamond Tools ICS 701-A Series Скачать руководство пользователя страница 8

© 2021 ICS, Oregon Tool International Inc.  Specifications are subject to change without notice.  REV10152021  F/N 573498

701-A SERIES OPERATOR’S MANUAL

8

THE FOLLOWING WARNING SYMBOL APPLIES TO ALL THE ITEMS LISTED 

ON THIS PAGE

Note:  Chain breakage can result in high-speed ejection of parts, which 

can result in death or serious personal injury to operators or bystanders.  

The items listed immediately below are critical to minimizing the risk of 

chain breakage and injury.

•  

DO NOT operate the power cutter with damaged, modified or missing 

   components shown below. 

 

 

•  Side cover

 

•  Mud flap

 

•  Rear hand guard

 

•  Mud flap bracket (chain catcher)

 

•  Trigger interlock

•  

DO NOT exceed 90 psi (6 bar) operating pressure.

•  

DO NOT insert the diamond chain power cutter into a slot narrower 

 

   than the chain segments.

  

   Rapid pushback might occur.  
   

NOTE:  Most ICS diamond chain segments are .225 inches (5.72 mm) wide.

•  

NEVER run a diamond chain power cutter upside-down.

  

   Concrete debris can fly back into the operator’s face. 

•  

NEVER cut ductile iron pipe with concrete chain. 

 

   Segment loss or chain breakage may occur.

•  

NEVER operate the ICS power cutter with a saw chain or saw bar 

 

   designed to cut wood. 

 

   Using wood cutting saw chain on the ICS power cutter could result in  
   severe injuries to operator and bystanders! Use ONLY the cutting  

   attachments specified in this manual on this power cutter.

SAFETY

   WARNING

Indicates a hazard with a medium level of risk 
which, if not avoided, could result in death or 
serious injury.

Содержание ICS 701-A Series






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды