Diamond Tools ICS 701-A Series Скачать руководство пользователя | Manualshive

Страница: 24 / 29

background image

© 2021 ICS, Oregon Tool International Inc. Specifications are subject to change without notice. REV10152021 F/N 573498

701-A SERIES OPERATOR’S MANUAL

24

•

SLOW CHAIN SPEED

- Be sure the compressor is providing the correct

air pressure at the power cutter (90 psi = 6 bar) and cubic feet per minute
(124 cfm = 3.5 m

3

/min). Chain is installed too tight. Refer to tension on

page 11. Low oil or no oil is getting to the motor. Make sure the drops per
minute (DPM) is set between 10 & 15.

•

CONCRETE CHAIN - POOR CUTTING PERFORMANCE

- Diamonds may

be “glazed over”. Make a few plunge cuts in an abrasive material such as a
cinder block to expose the diamonds.

•

UTILITY CHAIN - POOR CUTTING PERFORMANCE

- PowerGrit® chain is

worn out. Make sure the diamonds are intact and exposed. DO NOT use
PowerGrit for cutting steel.

•

PREMATURE CHAIN STRETCH

- Not enough water pressure, the

minimum water pressure is 20 psi (1.4 bar). Insufficient water supply will

result in excessive wear on the chain, which can lead to loss of strength
and chain breakage. Cutting with the guidebar nose buried in the cut, in
sand, gravel, pipe or using with improper chain tension will all contribute to
increased chain stretch.

NOTE: This applies to PowerGrit chains also.

•

CHAIN TENSIONER BREAKAGE

- Side cover nuts are not tight enough, or

tensioning was attempted with side cover nuts already fully tightened.

•

WATER NOT FLOWING

- Water hose is kinked, blockage in guidebar

water ports, or supply is not turned on.

•

MOTOR DOES NOT START

•

Insufficient air supply. Check compressor and air hose, valves, and air

inlet screen for blockage.

•

Chain tension is too tight, loosen chain tension.

•

Iced exhaust. wait until ice thaws, then use anti-freeze lubricant

•

Vanes sticky. Apply lubricant directly to power cutter air inlet and blow
motor clear. Repeat if necessary. See maintenance instructions

TROUBLESHOOTING

Further questions?

Call 800.321.1240 or visit our website at: icsdiamondtools.com

«
...
22
23
24
25
26
...
»

Содержание ICS 701-A Series






























Отзывы:

Нет отзывов

Похожие инструкции для ICS 701-A Series

Бренд: Makita Страницы: 4

Бренд: Garde Страницы: 4

Бренд: Dexter Power Страницы: 50

Бренд: Quality Commercial Macines Страницы: 4

Бренд: RHINO Страницы: 146

Бренд: Hitachi Страницы: 158

Бренд: Duratool Страницы: 4

Бренд: Performance Tool Страницы: 2

Бренд: O-Mac Страницы: 88

Бренд: Maruyama Страницы: 32

Бренд: Maruyama Страницы: 56

Бренд: Maruyama Страницы: 60

Бренд: N.KO Страницы: 16

Бренд: RASOR Страницы: 16

Бренд: TNT Rescue Страницы: 30

Бренд: EINHELL Страницы: 24

Бренд: EINHELL Страницы: 36

Бренд: Martin Yale Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды