Diamond Tools ICS 701-A Series Скачать руководство пользователя | Manualshive

Страница: 7 / 29

background image

701-A SERIES OPERATOR’S MANUAL

© 2021 ICS, Oregon Tool International Inc. Specifications are subject to change without notice. REV10152021 F/N 573498

7

SYMBOLS & LABELS

Mud flap

A barrier to protect the operator from cutting debris and other projectiles.

Powerhead

A power cutter without the chain or guidebar.

PSI

PSI means pounds per square inch. It measures how much force is in a

certain area – one pound-force applied to one square inch.

Pushback

The rapid backward motion of the guidebar, occurring when the chain on

the top straight portion of the guidebar contacts a foreign object or

snags in the workpiece.

Rear handle

The support handle located at or toward the rear of the power cutter

intended to be gripped by the right hand.

Rear hand guard:

A structural barrier at the bottom right side of the rear handle to protect the

operator in case the chain breaks or derails.

Side cover:

The component on the powerhead that covers the drive sprocket and

directs debris away from the operator during use.

Side cover nut:

The component on the side cover that secures the side cover and guide-

bar.

Throttle trigger lock-out

A device that prevents the unintentional operation of the throttle trigger

until manually released.

Throttle trigger

A mechanism that controls engine RPM.

WallWalker®

A device used as a fulcrum to provide mechanical advantage during cut-

ting.

Water shut-off valve

A mechanism that controls water delivery and flow to the guidebar and

chain.

«
...
5
6
7
8
9
...
»

Содержание ICS 701-A Series






























Отзывы:

Нет отзывов

Похожие инструкции для ICS 701-A Series

Бренд: Malco Страницы: 2

Бренд: Hilti Страницы: 196

Бренд: ZIPPER MASCHINEN Страницы: 76

Plasma 1000 V Series

Бренд: Multicam Страницы: 227

Бренд: Cobra Страницы: 27

Бренд: Bushranger Страницы: 36

SRM-2100 TYPE 1E - 02-99

Бренд: Echo Страницы: 29

Бренд: SteelMax Страницы: 42

Бренд: Lukas Страницы: 28

Бренд: G-WEIKE Страницы: 75

Бренд: Tupperware Страницы: 12

Бренд: Poulan Pro Страницы: 28

UNIVERSAL Comet CENTURY

Бренд: JB GURY Страницы: 32

Бренд: Safety Speed Manufacturing Страницы: 16

Hurricane MaX F-580BiS

Бренд: Vari Страницы: 64

PowerBlade 35-078

Бренд: IDEAL Страницы: 4

Бренд: GCE Страницы: 136

Бренд: Felker Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды