Diamond Products CC6571, Руководство оператора, Страница: 51 / 64

CC65
4. L
p
5. L
f
t
g
t
t
n
m
6.
O
p
u
7.
R
h
571 - CC6571-3
Locate detent
pulling outwar
Locate the b
front of the s
he lead scre
gear box to t
he lead scre
ension and
necessary. D
manufacture
Figure
Once the bla
properly, loc
until it snaps
Replace belt
head cap scr
3 Concrete Saw
t pin in front o
rd and turning
Figure 98: De
elt tensione
saw frame. T
ew clockwise
tilt back. To
ew counter c
readjust the
DO NOT exc
er’s belt tens
e 99: Belt Ten
ade drive bel
k the detent
s back into p
t guard and r
rew and bolt
w Manual
of the saw. Re
g 90

to lock
etent Pin
r lead screw
To loosen the
e. This will a
tighten the
clockwise. T
tension bolt
ceed the
ion setting.
sioner Lead S
lts are tighte
pin. Turn d
lace.
retighten the
ts.
etract pin by
open.
w on the
e belts turn
allow the
belts turn
Test the belt
t as
Screw
ened
detent pin
e seven hex
Rep
Sing
1
2
3
4
5
6
7
8
Thre
1. L
s
c
f
2. L
p
3.
L
f
t
g
e
t
c
t
t
lacing the Bl
gle Speed
1. Locate th
saw. Loo
head cap
side and
2. Locate th
the saw.
3. Locate th
front of t
4. Turning
will loose
5. Remove
from the
6. Loop an
around t
sheave,
loop and
near the
7. Adjust th
clockwis
tension a
necessa
manufac
8. Once the
properly
on the rig
guide.
ee Speed
Locate the b
saw. Loosen
cap screw a
front of saw.
Locate detent
pulling outwa
Locate the b
front of the s
the lead scre
gear box to
ease in remo
tighten the b
clockwise. T
the tension b
the manufac
lade Drive B
he belt guar
osen and rem
p screw and
d rear of saw
he engine g
. Loosen the
he belt tensi
the saw fram
the lead scr
en the tensio
e the belts fro
blade shaft
d align the n
the grooves
and then pu
d align them
e end of the P
he lead screw
se to tighten
and readjust
ary. DO NOT
cturer’s belt t
e blade drive
, retighten th
ght side of t
belt guard on
n and remov
and bolts loca
. Remove gu
t pin in front o
ard and turning
belt tensione
saw frame. T
ew clockwis
tilt back rele
oving and re
belts turn the
Test the belt
bolt as nece
cturer’s belt
Belts
rd on the left
move the se
d bolts locate
w. Remove b
uide on the
e hex head c
ioner lead sc
me.
rew counter
on on the be
om the PTO
t sheave.
new belts (on
on the blade
ull them upw
around the
PTO sheave
w by turning
the belts. Te
t the lead sc
T exceed the
tension setti
e belts are ti
he cap screw
he saw on th
n the left sid
ve the seven
ated on the
uard.
of the saw. R
g to lock open
er lead screw
To loosen th
e. This will
easing belt te
eplacing belt
e lead screw
t tension and
essary. DO N
tension setti
t side of the
even hex
ed on the
belt guard.
right side of
cap screws.
crew on the
clockwise
elts.
sheave and
ne at a time)
e shaft
ward and
grooves
e.
g the bolt
est the belt
crew as
e
ing.
ightened
ws located
he engine
e of the
n hex head
side and
Retract pin by
n.
w on the
he belts turn
allow the
ension for
ts. To
w counter
d readjust
NOT exceed
ing.
d
)
d
51