Diamond Products CC6571, Руководство оператора, Страница: 37 / 64

CC65
3.
4.
5.
571 - CC6571-3
Inhibit Sw
X to clos
Figure 6
. The turn
key when
engine d
seconds
another 3
DO NOT
continuo
Refer to
does not
Fi
. Increase
the engin
coolant te
55C/131
carbon/c
. Increase
the thrott
maximum
maximum
3 Concrete Saw
witch. Press
e the messa
65: Soft Key to
the key to
S
n the engine
does not catc
after key is
30 seconds
T allow the st
usly for mor
the engine m
t start after tw
gure 66: Disp
the engine
ne warm up
emperature
F. Avoid exc
oking build u
the engine
tle as necess
m efficiency.
m recommen
w Manual
the soft key
age.
o Close Windo
Start
, and rel
e starts.
Note
ch or start at
turned to St
and then be
tarter motor
re than 20 se
manual if the
wo attempts
lay Screen
to half thrott
without load
reaches ove
cessive idling
up and DPF
to full throttl
sary when c
DO NOT ex
nded blade R
y under the
ow
lease the
e: If the
t 10
tart, wait for
egin again.
to run
econds.
e engine
s
.
tle and let
d until the
er
g to prevent
plugging.
e. Adjust
cutting for
xceed the
RPM when
Stop
DO
eng
spi
1.
2.
3.
4.
5.
6.
7.
Con
DO
els
wh
Help
Kee
effic
Use
on th
the s
Avo
blad
Mov
or m
the s
leve
resta
DO
saw
to av
Task
Com
operating
Speed s
RPM.)
pping the En
CAUTIO
O NOT leave
gine is off an
nning.
Place th
Raise th
Turn off
Turn off
Turn off
Decreas
several m
idle the e
Turn the
ncrete Cut
WARNIN
O NOT expos
se to the dire
en operating
pful Hints Pri
ep the followi
ciency when
e just enough
he cutting lin
saw from sid
id sawing ex
de and reduc
ving too quic
may cause th
saw stalls at
er to
Neutral
art the engin
NOT lower t
w forward too
void forcing
ks Prior to C
mplete the fo
g the saw. (
section in this
ngine
ON
e the saw un
nd the blade
e speed con
e blade from
the water pu
the water sa
the water va
se the engine
minutes. Fo
engine for a
e key to
Stop
tting
NG
se yourself o
ect line of the
g the saw.
ior to Cutting
ing things in
cutting:
h handle pre
ne. DO NOT
de to side w
xcessively d
ce sawing co
ckly when cu
he blade to c
t any time, m
and raise th
ne.
the blade to
o quickly whe
the blade in
Cutting
ollowing task
Refer to the
s manual for
attended un
e has stoppe
ntrol lever at
m the cut
.
ump switch
afety switch.
alve.
e speed to id
or turbocharg
pproximately
p
and remov
or anyone
e blade
g
n mind for gre
essure to gui
T forcibly dire
hen cutting.
eep to prese
osts.
utting may st
climb out fro
move the spe
he blade from
o quickly or
en finishing
nto the concr
ks prior to cu
Blade
r correct
ntil the
ed
Neutral
.
if in use.
.
dle for
ged engines
y 5 minutes.
e the key.
eater
ide the saw
ect (twist)
erve the
tall the saw,
m the cut. If
eed control
m the cut to
move the
a partial-cut
rete.
utting:
,
37