diagenode Bioruptor Pico Скачать руководство пользователя страница 6

Страница: 6 / 48

BIORUPTOR

PICO

MANUAL

Critical steps for maintenance
and efficient shearing

General warnings

Sonication bath temperature

• Optimal temperature for sonication is 4°C. Sample temperature should not exceed 8°C.

• The Bioruptor Cooler (Cat. No. B02010010, B02010011, B02010012) has to be used to guarantee the

automatic temperature control of the sonication bath during the entire sonication process.

Validated tubes for the Bioruptor

Pico

• DNA shearing: 0.2 ml (Cat.No. C30010020) and 0.65 ml (New Cat. No. C30010011; Old Cat. No. WA-005-

0500) Bioruptor

Microtubes for DNA shearing.

• Chromatin shearing: 0.2 ml (Cat.No. C30010020) and 1.5 ml (Cat.No. C30010016) Bioruptor

Microtubes

and 15 ml (Cat.No. C01020031) Bioruptor

Tubes & sonication beads.

Fitting tubes in the tube holder

• Place the tubes in the corresponding tube holder. Never leave empty spaces in the tube holder. Fill the

empty spaces with tubes containing the same volume of water. Screw the lid on the tube holder without
over-tightening it.

• Carefully place the tube holder on the holding plate.

• During sonication, samples must remain at the bottom of the tube. If needed, briefly centrifuge samples

during sonication after pausing the run.

DON’T

Turn on the instrument without water

Exceed 30 min of total sonication

Tilt the sonication unit

Change water at least once every month

Use deionized or distilled water

QC your system with our DNA QC Kit

Содержание Bioruptor Pico

















































Результаты поиска

Содержание Bioruptor Pico

Отзывы:

Бренды по названию

Популярные бренды

diagenode Bioruptor Pico, Руководство пользователя

Результаты поиска

Содержание Bioruptor Pico

Отзывы:

Бренды по названию

Популярные бренды