manualshive.com logo in svg

diagenode Bioruptor Pico, Руководство пользователя

Поделиться
Скачать
diagenode Bioruptor Pico Скачать руководство пользователя страница 36

36

 

BIORUPTOR

®

 PICO

    MANUAL 

Operation

Switching on the device

Personnel: Operating personnel

NOTICE! 

Overheating of the compressor

Device damage

•  Never operate water cooled device without cooling water.

1.   

Switch on the device using the mains power switch. A signal tone sounds. The software 
version  is  shown  on  the  display.  The  actual  temperature  is  shown  on  the  dis-  play 
afterwards.  The  temperature  control  device  starts  operation;  the  pumps  are  started.
Depending on the specified set point temperature, the refrigerant unit is started after 2 
minutes at the earliest. The blue LED lights if the refrigerant unit is active.

2.   

Depending on the water level, heat transfer liquid must be refilled if necessary. Monitor 
the level indicator for this.

Default display and set point temperature

1.   

Press the ENTER button to reach set point menu from the default display of the actual 
temperature.

If no button has been pressed for longer than 4 seconds, you exit from the set point menu.

2.   

Select a set point temperature (between 2°C and 20°C) using the arrow buttons.

3.   

The changed value or setting is applied immediately by pressing the ENTER button

Standby mode

The Display shows: “STBY” alternating with the bath temperature.

The device goes into Standby mode if no 24V signal from the Bioruptor is received for a 
period of time of more than 2 hours.

In Standby mode the compressor and the pumps are turned off.

If during Standby mode the bath temperature reaches a value higher than 10 K above the set 
point, the compressor and the pumps turn on automatically to cool down to set point. The 

Содержание Bioruptor Pico

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды