Di-LOG DL6507 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 16

Di-LOG DL6507 Скачать руководство пользователя страница 3

Introduction

References marked on instrument or
in instruction manual:

Warning of a potential danger, comply with
instruction manual.

Reference. Please use upmost attention.

Caution! Dangerous voltage. Danger of
electrical shock.

Symbol for the marketing of electrical and
electronic equipment

(WEEE Directive 2002/96/EC).

Continuous double or reinforced insulation
complies with category II IEC 536.

Conformity symbol, the instrument complies with
the valid directives. It complies with the EMV
Directive (89/336/EEC), Standards EN 50081-1
and EN 50082-1 are fulfilled. It also complies with
the Low Voltage Directive (73/23/EEC), Standard
EN 61010-1 is fulfilled.

The instruction manual contains information
and references, necessary for safe operation and
maintenance of the instrument.

PRIOR TO USING THE INSTRUMENT THE USER IS KINDLY
REQUESTED TO THOROUGHLY READ THE INSTRUCTION
MANUAL AND COMPLY WITH IT IN ALL SECTIONS.

Failure to read the instruction manual or to
comply with the warnings and references
contained herein can result in serious bodily
injury or instrument damage.

Safety Information

«
1
2
3
4
5
...
»

Содержание DL6507

















Отзывы:

Нет отзывов