Di-LOG DL6507 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 16

Di-LOG DL6507 Скачать руководство пользователя страница 11

Operating Instructions

Resistance measurements

Disconnect the circuit from all sources of supply
and check that it is at zero voltage.

• Turn selector switch (2) to “V

Ω

”

• Plug the black test lead into the “COM” socket and

the red lead into the “+” socket

• Connect the probes to the circuit and read the

display

If the display is not visible during measurement,
press the “HOLD” button (3) to retain the display.
The probes can then be removed from the
conductor and the stored value read.

MIN/MAX and peak values

The MIN/MAX button can be used to find either the
largest or the smallest value of a series of measurements.
Pressing the MIN/MAX button activates first the MIN
mode, so that the smallest value is selected. Pressing it a
second time changes to MAX mode, for the largest value.
Pressing the button a third time returns the instrument
to normal operation.

6.0 Maintenance

Provided it is used in accordance with the Instruction
Manual, the instrument needs no special maintenance.

Operating Instructions

«
...
9
10
11
12
13
...
»

Содержание DL6507

















Отзывы:

Нет отзывов