DFI PE21-EC страница 9 Скачать руководство пользователя | Manualshive

Страница: 9 / 123

background image

1

Introduction

9

I/O Connectors

• Two connector s for 4 additional external USB 2.0 por ts

(compliant with USB 1.1)

• One connector for external line-out and mic-in jacks
• Two internal audio connectors (AUX-in and CD-in)
• One 4-channel audio output connector (PE21-EC/A and

PE21-EL/A only)

• One S/PDIF-in connector (PE21-EC/A and PE21-EL/A only)
• One S/PDIF-out connector (PE21-EC/A and PE21-EL/A only)
• One connector for IrDA interface
• Two IDE connectors
• One floppy drive interface supports up to two 2.88MB floppy

drives

• Two ATX power supply connectors
• One Wake-On-LAN connector
• One Wake-On-Ring connector
• CPU fan, chassis fan and second chassis fan connectors

PCI Bus Master IDE Controller

• Two PCI IDE interfaces support up to four IDE devices
• Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives
• UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate

up to 133MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer
• Suppor ts ATAPI CD-ROM, LS-120 and ZIP

S/PDIF (PE21-EC/A and PE21-EL/A only)

The  system  board  is  equipped  with  the  S/PDIF  (Sony/Philips  Digital
Interface)  digital  audio  interface.  S/PDIF  is  a  standard  audio  file
transfer format that transfers digital audio signals to a device without
having  to  be  conver ted  first  to  an  analog  format. This  prevents  the
quality  of  the  audio  signal  from  degrading  whenever  it  is  conver ted
to analog.

IrDA Interface

The mainboard is equipped with an IrDA connector for wireless
connectivity between your computer and peripheral devices.

«
...
7
8
9
10
11
...
»

Содержание PE21-EC




























































































































Отзывы:

Нет отзывов

Похожие инструкции для PE21-EC

Бренд: Yamaha Страницы: 90

Бренд: SOLTEK Страницы: 49

Бренд: ST Страницы: 77

Бренд: Texas Instruments Страницы: 16

Бренд: ASROCK Страницы: 144

PRESTIGE X570 CREATION

Бренд: MSI Страницы: 88

Blood-Iron P45 Elite Series

Бренд: LanParty Страницы: 134

LPC1768-Xplorer

Бренд: NGX Technologies Страницы: 25

Бренд: BOSER Technology Страницы: 38

Бренд: Biostar Страницы: 32

Бренд: Systium Technologies Страницы: 4

Бренд: Analog Devices Страницы: 8

BD93F10MWV-EVK-001

Бренд: Rohm Страницы: 20

Бренд: DFI Страницы: 105

Бренд: Asus Страницы: 82

Бренд: Asus Страницы: 46

Бренд: Asus Страницы: 48

Бренд: Asus Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды