DFI BT700 Скачать руководство пользователя страница 22

Страница: 22 / 52

www.dfi .com

Chapter 3 BIOS Setup

Chapter 3

SATA Configuration

This section is used to configure the settings of SATA device.

Enable/Disable Serial
ATA

SATA Confi guration

Serial-ATA (SATA)

Serial-ATA Port 0
Serial-ATA Port 1

SATA Port0
Not Present

SATA Port1
Not Present

Advanced

Serial ATA Port 0 and 1

This field is used to enable or disable the Serial ATA port 0 and 1.

[Enabled]

[Enabled]
[Enabled]



Select Screen



Select Item

Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Reset
ESC: Exit

LPSS & SCC Configuration

This section is used to configure the LPSS & SCC settings.

LPSS I2C #1 Support
Enable/Disable

LPSS Confi guration

LPSS I2C #1 Support

LPSS HSUART #1 Support
LPSS HSUART #2 Support
LPSS SPI Support

Advanced

LPSS I2C #1 Support

Enable or disable the support of the LPSS I2C device.

LPSS HSUART #1/#2 Support

Enable or disable the support of the LPSS HSUART device.

LPSS SPI Support

Enable or disable the support of the LPSS SPI device.

[Enabled]

[Enabled]
[Enabled]
[Enabled]



Select Screen



Select Item

Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Reset
ESC: Exit

Содержание BT700





















































Результаты поиска

Содержание BT700

Отзывы:

Похожие инструкции для BT700

Бренды по названию

Популярные бренды

DFI BT700, Руководство пользователя

Результаты поиска

Содержание BT700

Отзывы:

Похожие инструкции для BT700

Бренды по названию

Популярные бренды