background image

Page 2 of 12

Dewhot | Gas geyser manual

Read these instructions carefully before operating the 

gas geyser and familiarize yourself with the appliance 

before connecting it to the gas cylinder.  Keep these 

instructions for future reference. 

This appliance is manufactured to operate on LPG 

only. Do not tamper or modify the appliance.

If you smell gas

1.  Turn off the gas supply at the bottle
2.  Extinguish all naked flames
3.  Do not operate any electrical 

appliances

4.  Ventilate the area
5.  Check for leaks as described in this 

manual

6.  If gas smell persists, contact your 

dealer or gas supplier immediately

Burn-back 

In the event of a burn-back, where the 
flame burns back to the jet, immediately 
turn the gas supply off at the gas cylinder.  
After ensuring the flame is extinguished, 
wait for I minute and then reignite the 
appliance as per normal.  Should the 

appliance burn back again, close the gas 
cylinder and call a registered LPG installer.  
Do not use the appliance again until the 
installer has confirmed that it is safe to do 
so. 

Gas-pressure regulator 

This appliance requires an operating 
pressure of 2,8 kpa.  Only install a LPG 
regulator that complies with the SANS 1237 
requirements.

Guarantee

Should you to want to make a guarantee 
claim, you will need to supply your invoice 
and Certificate of Compliance (COC)

Important

Содержание LPDH 5













Отзывы: