35
EnGLIsh
Safety Instructions for Mitre Saws
a )
Mitre saws are intended to cut wood or wood-like products,
they cannot be used with abrasive cut-off wheels for cutting
ferrous material such as bars, rods, studs, etc.
Abrasive dust
causes moving parts such as the lower guard to jam. Sparks from
abrasive cutting will burn the lower guard, the kerf insert and other
plastic parts.
b )
Use clamps to support the workpiece whenever possible. If
supporting the workpiece by hand, you must always keep your
hand at least 100 mm from either side of the saw blade. Do
not use this saw to cut pieces that are too small to be securely
clamped or held by hand.
If your hand is placed too close to the saw
blade, there is an increased risk of injury from blade contact.
c )
The workpiece must be stationary and clamped or held against
both the fence and the table. Do not feed the workpiece into
the blade or cut “freehand” in any way.
Unrestrained or moving
workpieces could be thrown at high speeds, causing injury.
d )
Push the saw through the workpiece. Do not pull the saw
through the workpiece. To make a cut, raise the saw head
and pull it out over the workpiece without cutting, start the
motor, press the saw head down and push the saw through
the workpiece.
Cutting on the pull stroke is likely to cause the saw
blade to climb on top of the workpiece and violently throw the blade
assembly towards the operator.
e )
Never cross your hand over the intended line of cutting either
in front or behind the saw blade.
Supporting the workpiece “cross
handed” i.e. holding the workpiece to the right of the saw blade with
your left hand or vice versa is very dangerous.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
1) Work Area Safety
a )
Keep work area clean and well lit.
Cluttered or dark areas
invite accidents.
b )
Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust.
Power tools
create sparks which may ignite the dust or fumes.
c )
Keep children and bystanders away while operating a power
tool.
Distractions can cause you to lose control.
2) Electrical Safety
a )
Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
b )
Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators.
There is an increased
risk of electric shock if your body is earthed or grounded.
c )
Do not expose power tools to rain or wet conditions.
Water
entering a power tool will increase the risk of electric shock.
d )
Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat,
oil, sharp edges or moving parts.
Damaged or entangled cords
increase the risk of electric shock.
e )
When operating a power tool outdoors, use an extension cord
suitable for outdoor use.
Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f )
If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply.
Use of an
RCD reduces the risk of electric shock.
3) Personal Safety
a )
Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while
you are tired or under the influence of drugs, alcohol or
medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b )
Use personal protective equipment. Always wear eye
protection.
Protective equipment such as dust mask, non-skid safety
shoes, hard hat or hearing protection used for appropriate conditions
will reduce personal injuries.
c )
Prevent unintentional starting. Ensure the switch is in the off-
position before connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with
your finger on the switch or energising power tools that have the
switch on invites accidents.
d )
Remove any adjusting key or wrench before turning the power
tool on.
A wrench or a key left attached to a rotating part of the
power tool may result in personal injury.
e )
Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f )
Dress properly. Do not wear loose clothing or jewellery. Keep
your hair and clothing away from moving parts.
Loose clothes,
jewellery or long hair can be caught in moving parts.
g )
If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly
used.
Use of dust collection can reduce dust-related hazards.
h )
Do not let familiarity gained from frequent use of tools allow
you to become complacent and ignore tool safety principles.
A
careless action can cause severe injury within a fraction of a second.
4) Power Tool Use and Care
a )
Do not force the power tool. Use the correct power tool for your
application.
The correct power tool will do the job better and safer at
the rate for which it was designed.
b )
Do not use the power tool if the switch does not turn it on and
off.
Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
c )
Disconnect the plug from the power source and/or remove the
battery pack, if detachable, from the power tool before making
any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power
tool accidentally.
d )
Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous
in the hands of untrained users.
e )
Maintain power tools and accessories. Check for misalignment
or binding of moving parts, breakage of parts and any other
condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use.
Many
accidents are caused by poorly maintained power tools.
f )
Keep cutting tools sharp and clean.
Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control.
g )
Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working
conditions and the work to be performed.
Use of the power
tool for operations different from those intended could result in a
hazardous situation.
h )
Keep handles and grasping surfaces dry, clean and free from oil
and grease.
Slippery handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected situations.
5) Service
a )
Have your power tool serviced by a qualified repair person
using only identical replacement parts.
This will ensure that the
safety of the power tool is maintained.
Содержание DWS727
