background image

3

b)  

Do not use the power tool if the switch does not turn it on and off. 

Any 

power tool that cannot be controlled with the switch is dangerous and must 

be repaired.

c)  

Disconnect the plug from the power source and/or the battery pack from 

the power tool before making any adjustments, changing accessories, 

or storing power tools. 

Such preventive safety measures reduce the risk of 

starting the power tool accidentally.

d)  

Store idle power tools out of the reach of children and do not allow 

persons unfamiliar with the power tool or these instructions to operate the 

power tool. 

Power tools are dangerous in the hands of untrained users.

e) 

 Maintain power tools. Check for misalignment or binding of moving parts, 

breakage of parts and any other condition that may affect the power tool’s 

operation. If damaged, have the power tool repaired before use. 

Many 

accidents are caused by poorly maintained power tools.

f) 

 Keep cutting tools sharp and clean. 

Properly maintained cutting tools with 

sharp cutting edges are less likely to bind and are easier to control.

g) 

  Use the power tool, accessories and tool bits, etc. in accordance with 

these instructions, taking into account the working conditions and the work 

to be performed. 

Use of the power tool for operations different from those 

intended could result in a hazardous situation.

5) SERVICE

a)  

Have your power tool serviced by a qualified repair person using only 

identical replacement parts. 

This will ensure that the safety of the power tool 

is maintained.

Electrical Safety

The electric motor has been designed for one voltage range only. Always check that 

the power supply corresponds to the voltage on the rating plate. 220–240 V AC 

means your tool will operate on alternating current. Operation at a voltage outside this 

range can cause loss of power and can result in overheating. All D

E

WALT tools are 

factory tested; if this tool does not operate, check the power supply. Your D

E

WALT 

tool is double insulated, therefore no earth wire is required.
 • 

Young children and the infirm.

 This appliance is not intended for use by young 

children or infirm persons without supervision. 

    –  This appliance is not intended for use by persons (including children) with 

reduced physical, sensory or mental capabilities, or lack of experience and 

knowledge, unless they have been given supervision or instruction concerning 

use of the appliance by a person responsible for their safety.

    –  Children should be supervised to ensure that they do not play with the appliance.
  •

  Replacement of the supply cord. 

If the supply cord or plug is damaged, it must 

be replaced by the manufacturer or an authorised D

E

WALT Service Centre in 

order to avoid a hazard.

Extension Cords

CAUTION: 

Use only extension cords that are approved by the country’s Electrical 

Authority. Before using extension cords, inspect them for loose or exposed wires, 

damaged insulation and defective fittings. Replace the cord if necessary.

Tool Safety Warnings

 • 

Hold power tool by insulated gripping surfaces, because the cutter may 

contact its own cord.

 Cutting a “live” wire may make exposed metal parts of the 

power tool “live” and shock the operator.

 • 

Use clamps or another practical way to secure and support the workpiece 

to a stable platform.

 Holding the work by hand or against your body leaves it 

unstable and may lead to loss of control.

  •  Accessories must be rated for at least the speed reccomended on the tool 

warning label. Accessories running over rated speed can fly apart and cause 

injury. Accessory ratings must always be above the tool speed as shown on tool 

nameplate.

  •  DO NOT CUT METAL. 
  •  Keep handles and gripping surfaces dry, clean, and free from oil and grease. This 

will enable better control of the tool.

  •  Maintain firm grip with both hands on laminate trimmer to resist starting torque.
  •  Keep hands away from cutting area. Never reach under the workpiece for any 

reason. Keep the laminate trimmer base firmly in contact with the workpiece 

when cutting. These precautions will reduce the risk of personal injury.

  •  Never run the motor unit when it is not inserted into the base. The motor is not 

designed to be handheld.

  •  Keep cutting pressure constant. Do not overload motor.

Содержание DWE6005-XE

















Отзывы: