ENGLISH
29
WARNING:
115 V units have to
be operated via a fail-safe isolating
transformer with an earth screen
between the primary and secondary
winding.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D
E
WALT service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
• Connect green / yellow lead to the earth
terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3-core extension cable suitable for the power
input of this tool (see technical data).The minimum
conductor size is 1.5 mm
2
; the maximum length is
30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing
set- ups or when making repairs.
Be sure the switch is in the OFF
position. An accidental start-up can
cause injury.
Installing the Machine (fi g. 2–5)
1. Assemble the feed handle.
2. Mount the drill guard (j).
3. Fit the lubrication system as necessary.
4. Place the machine on a clean, level and solid
surface. Remove any particles that will obstruct
full contact between the magnetic stand and
the mounting surface.
5. Fit and tighten the safety chain (o).
MOUNTING THE FEED HANDLE ASSEMBLY (FIG. 1, 2)
The quick-release feed handle assembly can be
mounted in one simple operation both to the left and
the right of the machine.
1. Screw all three feed handles (f) into the hub (g).
2. Keep the button (p) depressed while inserting
the hub shaft into the hole (q).
3. Release the button.
MOUNTING THE DRILL GUARD (FIG. 3)
1. Hold the guard (j) in front of the tool holder,
aligning the slots in the guard with the holes in
the machine.
2. Fit the screw (r) into the hole (s) located in the
front of the frame.
WARNING:
Always use the drill guard.
FITTING THE LUBRICATION SYSTEM (FIG. 1, 4)
The lubrication system can be used for horizontal
drilling applications (the drill being used vertically).
1. With the coolant bottle (k) placed into the
magnetic bracket (e), mount the magnetic
bracket onto the steel strip (t) on either side of
the tool.
2. Attach the coolant tube (l) to the coolant bottle:
a.
Remove the nut (u) and thread it with the
tube.
b.
Slide the tube onto the nipple and tighten the
nut.
3. Attach the tube to the quick-release connector
(v) on the gearbox
a.
Push coolant tube (l) in to install.
b.
To remove, push the collar on the connector
(v) in and pull the tube from the connector.
In order to use the lubrication system, the coolant
bottle (k) must be filled with a sufficient amount of
cutting fluid.
Filling the Coolant Bottle
1. Make sure the flow regulator (m) is closed.
2. Unscrew the cap (x).
3. Fill the container with cutting coolant diluted
with water.
4. Screw the cap back on.
WARNING:
Do not use the lubrication
system in vertical or overhead drilling
applications.
Содержание DWE1622
