DeWalt DW849-XE, Инструкция по эксплуатации

Страница: 8 / 12

6
the switch may be locked in its full on position and
A
FIGURE 3
tool speed changed by means of the speed control
wheel alone.
The electronic speed control not only lets you
select the speed to suit the job, but also helps
to maintain that speed as you load the tool by
pressing down. It’s this feature, coupled with the
variable speed switch, that make this tool such a
value.
The speed control wheel can be set for any speed between 1000 and 3000 RPM and
the variable speed switch will then control tool speed from zero to the wheel setting.
For example: A control wheel setting of 2200 RPM will allow the variable speed switch
to operate the tool between zero and 2200 RPM, depending on how far the trigger is
depressed. A wheel setting of 1000 RPM would allow the switch to operate the tool
from zero RPM to 1000 RPM.
The electronic speed control feature comes into play whenever the trigger switch is
fully depressed and the tool is running at the selected speed determined by the setting
of the control wheel. As you load the tool by pushing it down on the work surface,
(with the trigger fully depressed) the electronic circuit inside the tool will compensate
for the loading and maintain the selected speed. If the speed selected by the control
wheel is 2200 RPM, as in the example below, the tool will maintain 2200 RPM, as it
is loaded.
It is important to remember two things about electronic speed control:
1. The electronic speed control operates only when the trigger switch is fully
depressed.
2. The effect of electronic speed control is much easier to observe at lower speed
settings (2600 RPM and below), than at high speeds.
As the tool approaches 3000 RPM, the effect is considerably less dramatic.
Keep in mind that, with a conventional polisher running at a typical no load speed
of 2400 RPM, the tool slows down to about 2000 RPM under a polishing load. Your
DW849-XE will continue to run at 2400 RPM (or any speed you select with the control
wheel) as a load is applied. Since it doesn’t slow down, the speed may be greater
than you’re used to so some extra caution should be observed until you get the “feel”
of your polisher. If you feel the speed is too great, you can, of course slow the tool
down with either the trigger switch or the control wheel.
Spindle Lock Button (Figure 4)
E
FIGURE 4
In order to prevent the spindle of the tool from rotating
while installing or removing accessories, a spindle
lock button has been provided in the gear head of the
machine. To lock the spindle, depress and hold the
lock button (E). NEVER DEPRESS THE SPINDLE LOCK
BUTTON WITH THE TOOL RUNNING OR COASTING.
Attaching and Removing Polishing Pads
(Figure 5, 6)
WARNING: Shock Hazard . To reduce the risk of
serious personal injury, turn tool off and disconnect tool
from power source before making any adjustments or
removing/installing attachments or accessories.
G
H
I
J
FIGURE 5
To attach pad, push the hub of the clamp washer (G)
through the hole in the centre of the polishing pad (H)
as far as it will go. Engage the hexagonal hole in the
backing pad (I). Holding the three pieces firmly together,
place the assembly on the tool spindle (J). Hold the
spindle lock button while turning the pads clockwise to
thread them completely on the spindle.
To remove the pads, manually turn the pads in the
opposite directon from normal rotation to allow lock
button to engage spindle, then unscrew pads in normal
direction for right hand thread.
NOTE: If you are using a polishing bonnet (K), rather than
K
FIGURE 6
a pad, put clamp washer on first, pull bonnet completely
over backing pad and pull draw strings tight. Tie bow
knot and push knot and all loose string completely under
the inside, cloth edge of the polishing bonnet.
WARNING: TIED KNOT AND ALL STRINGS MUST BE
TUCKED ENTIRELY UNDER THE CLOTH APRON. FAILURE
TO DO SO MAY CAUSE SERIOUS INJURY.