24
EngLIsh
5. Place a new belt over the pulleys
20
, making sure that the
arrow on the inside of the belt points in the same direction
as the arrow
21
on the backing plate.
6. Release the lever.
7. Holding the threaded pin
22
in its place, replace the
backing plate.
8. Replace the knob and tighten it.
WARNING:
When mounting a leather honing belt, make
sure that the leather surface is on the outside.
Adjusting the Grinding or Honing Belt
(Fig. E)
Centering the Belt
1. If the belt
5
is not properly centered, adjust by turning the
centering knob
8
.
2. Slacken the hexagonal head bolts
23
and adjust the
plate
24
to minimise the clearance with the belt. Tighten
the bolts
Adjusting the Belt to the Workpiece
The belt can be adjusted to suit workpieces with concave,
convex or straight cutting edges.
1. Slacken the knob
10
.
2. Set the backing plate
18
to the appropriate position (up,
flush or down).
3. Tighten the knob
10
.
Preparing the Honing Belt For Use
Leather honing belts must be dressed before first use and when
the honing effect decreases.
With the machine switched off, spread a thin and even coating
of honing paste over the entire outside surface of the belt.
Mounting the Spark Guard (Fig. F, G)
The spark guard offers additional protection from sparks and
must be used whenever possible.
1. Fit the transparent screen
25
to the spark guard
6
by
inserting a mushroom head bolt
26
into the screen and the
guard and placing a washer
27
and nut
28
onto the bolt
(Fig. F). Tighten the nut.
2. Hold the spark guard against the edge on top of the wheel
case
29
as shown (Fig. G).
3. Insert a mushroom head bolt
30
into the guard and the
wheel case.
4. Place a washer
31
and nut
32
onto the bolt and tighten
the nut hand-tight.
5. Position the guard at a distance of approx.
2 mm from the wheel by sliding it towards the wheel.
6. Securely tighten the nut (torque: 6 Nm).
Adjusting the Workpiece Support (Fig. H)
The workpiece support can be set according to the workpiece
and the desired grinding angle.
1. Slacken the nut holding the support
3
.
2. Set the support to the desired position and angle, making
sure that the support is as close to the wheel as possible.
3. Tighten the nut (torque: 6 Nm).
Mounting and Adjusting the Clamping and
Grinding Attachment (Fig. A, I)
The clamping and grinding attachment is used to hold the
workpiece to the grinding wheel at a fixed angle.
1. Remove the fasteners holding the workpiece support
3
to
the bracket
4
and remove the workpiece support (Fig. A).
2. Mount the grinding attachment bracket
33
to the
bracket
4
on the machine as shown using the hexagonal
head bolt
34
and corresponding nut
35
(Fig. I). Make sure
that the grinding attachment bracket is at a distance of
approx. 2 mm from the grinding wheel.
3. Insert the rod
36
of the grinding attachment into the forks
on the grinding attachment bracket as shown.
Mounting the Water Supply System
(Fig. D, J–M)
1. Remove the backing plate
18
(Fig. D).
2. Insert a screw
37
into each of the bracket pairs
38
and
place a nut
39
a few turns on each screw (Fig. J).
3. Hook the bracket pairs
38
to the back of the belt case
40
as shown (Fig. K).
4. Hold the water reservoir
41
against the bracket pairs as
shown and push it in its place with the brackets engaging in
the recesses
42
.
5. Tighten the nuts
39
(Fig. J).
6. Replace the backing plate
18
(Fig. D).
7. Mount the flow regulator unit
43
to the front of the belt
case
40
using the screws
44
(Fig. L).
8. Place the hose
45
between the water reservoir
41
and the
flow regulator unit
43
(Fig. M).
9. In order to use the water supply system, it must be filled
with a sufficient amount of water.
a. Make sure the flow regulator
46
is closed.
b. Unscrew the cap
47
.
c. Fill the container with cold water.
d. Screw the cap
47
back on.
OPERATION
Instructions for Use
WARNING:
Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Содержание DW755
