DeWalt DW755, Оригинальное руководство пользователя

Страница: 25 / 96

23
EngLIsh
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The date code 51 , which also includes the year of manufacture,
is printed into the housing.
Example:
2018 XX XX
Year of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
1
On/off switch
2 Grinding wheel
3
Workpiece support
4
Bracket
5
Honing belt
6
Spark guard
7
Tensioning lever
8
Centering knob
9
Water supply system
10
Honing support knob
Intended Use
Your D
e
WALT tool grinding and honing machine was developed
for sharpening and honing knives, chisels and other cutting
tools. The machine is never to be used for grinding magnesium
tools. The machine is intended for intermittent use only.
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
The grinding and honing machine is a professional power tool.
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Unpacking the Machine and its Parts
1. Carefully lift the machine out of its package.
2. Take out the accessories and hardware parts.
Required and Recommended Tools
Apart from the tools included with the machine, the following
tools are required:
- Torque wrench
Mounting the Machine to the Workbench
(Fig. B)
The machine must be mounted onto the workbench.
1. Mark the position of the four mounting holes provided in
the base of the machine on the workbench.
2. Drill a Ø 6.5 mm hole at each of the marked positions.
3. Place the machine on the workbench and insert an M6 bolt
with a washer through the mounting holes in the base into
each of the holes drilled in the workbench. Make sure the
protruding length X (see Figure) is at least 15 mm for each
of the bolts used.
4. Place a nut on each of the bolts and securely tighten the
nuts (torque: 8 Nm).
Changing the Grinding Wheel (Fig. C)
1. Remove the three nuts
11
using the spanner supplied.
2. Remove the guard cover 12 .
3. Remove the nut 13 from the spindle 14 using the
spanner supplied.
4. Take the outer flange
15
, the packing piece
16
and the
wheel 17 from the spindle.
5. Place the new wheel onto the spindle.
6. Replace the packing piece, the outer flange and the nut on
the spindle.
7. Securely tighten the nut 13 (torque: 6 Nm).
8. Replace the guard cover.
9. Replace the three nuts
11 and securely tighten them
(torque: 5 Nm).
10. Switch on the machine and let the wheel run with no load
for one minute to check for cracks.
WARNING: Do not use a damaged wheel.
Changing the Grinding or Honing Belt
(Fig. D)
1. Remove the knob
10
.
2. Remove the backing plate 18 .
3. Turn the tensioning lever
7
counter-clockwise to release
tension and keep the lever in this position.
4. Remove the belt
19
.