DeWalt DW708, Руководство пользователя

Страница: 30 / 116

en - 7 23
E N G L I S H
• Set the mitre angle to the nearest whole degree desired by aligning the
centre mark in the vernier scale, shown in (fig. P1), with the whole
degree number etched in the mitre scale. Examine (fig. P1) closely;
the setting shown is 24° right mitre.
• To set the additional 1 /
2
°, squeeze the mitre arm lock and carefully
move the arm to the right until the
1
/
2
° vernier mark aligns with the
closest degree mark on the mitre scale. In this example, the closest
degree mark on the mitre scale happens to be 25°. Fig. P2 shows a
setting of 24
1
/
2
° right mitre.
When mitring to the right:
- increase the mitre angle by moving the arm to align the appropriate
vernier mark with the closest mark on the mitre scale to the right.
- decrease the mitre angle by moving the arm to align the appropriate
vernier mark with the closest mark on the mitre scale to the left.
When mitring to the left:
- increase the mitre angle by moving the arm to align the appropriate
vernier mark with the closest mark on the mitre scale to the left.
- decrease the mitre angle by moving the arm to align the appropriate
vernier mark with the closest mark on the mitre scale to the right.
Cutting base mouldings (fig. Q1 - Q4)
Vertical position
• Always make a dry run without power before making any cuts.
Straight 90° cuts (fig. Q1)
• Position the wood against the fence as shown in fig. Q1.
• Turn the saw ON, allow the blade to reach full speed and lower the arm
smoothly through the cut.
45° mitre cuts (fig. Q2)
• Position the moulding as shown in fig. Q2.
• All cuts are made with the back of the moulding against the fence and
the bottom of the moulding against the base.
Inside corner
- Left side
• Mitre left 45°.
• Save the left side of the cut.
- Right side
• Mitre right 45°.
• Save the right side of the cut.
Outside corner
- Left side
• Mitre right 45°.
• Save the left side of the cut.
- Right side
• Mitre left 45°.
• Save the right side of the cut.
Horizontal position using bevel (fig. M3)
Another method of making the cut is to make a 0° mitre, 45° bevel cut.
All cuts are made with the back of the moulding laying flat on the saw as
shown in fig. M3.
Inside corner
- Left side
• Position the moulding with top of the moulding against the fence.
• Save the left side of the cut.
- Right side
• Position the moulding with the bottom of the moulding against the fence.
• Save the left side of the cut.
Outside corner
- Left side
• Position the moulding with the bottom of the moulding against
the fence.
• Save the right side of the cut.
- Right side
• Position the moulding with top of the moulding against the fence.
• Save the right side of the cut.
Grooving (fig. R)
Your saw is equipped with a grooving stop (22) and thumbscrew (21) to
allow for groove cutting.
• Flip the grooving stop (22) towards the front of the saw.
• Adjust the thumbscrew (21) to set the depth of the groove cut.
Cutting non-ferrous metals
When cutting non-ferrous metals, the machine is only to be used to
perform vertical straight and mitre cross-cuts in the mitre saw mode.
We recommend that bevel and compound mitre cuts should not be
performed in non-ferrous metals. The machine is not to be used for cutting
ferrous metals.
• Always use a material clamp when cutting non-ferrous metals.
Make sure that the workpiece is clamped securely.
• Only apply saw blades that are qualified for cutting non-ferrous metals.
• When using lubricants, only apply wax or separation spray. Do not use
emulsions or similar fluids.
• Connect an FI or DI switch between machine and mains to avoid
residual risks caused by metal swarf.
The FI switch should comply with the following specifications:
rated voltage 230 V
rated current 16 A
reaction time < 15 ms
fusing current 30 mA
The DI switch should comply with the following specifications:
DIN VDE 0661
rated voltage 230 V
rated current 16 A
fusing current 30 mA
all-pole cutoff L+N+PE
PE monitoring
low-voltage release
Consult your dealer for further information on the appropriate accessories.
These include various saw blades, extension kits (DE7080), adjustable
length stops (DE7051), vertical clamps (DE7082), crown stops (DE7084)
and dustbags (DE7053).
Transport (fig. A1, A2 & B)
In order to conveniently carry your saw, a carrying handle (9) has been
included on the top of the saw arm (fig. B).
• To transport the saw (fig. B), lower the arm and depress the lock down
pin (16) (fig. A1).
• Mitre the saw 60° to the right, lock the mitre lever (4), lock the rail lock
knob (20) with the head fully forward, slide the fences (7) completely
inward and lock the bevel lever (11) with the saw at 0° bevel.
• Always use the carrying handle (18) and/or the handholds (24) (fig. A2)
to transport the saw.