17
E N G L I S H
en - 4
• Before replacing the top cover of the mains plug
ensure that the cable restraint (3) is holding the
outer sheath of the cable firmly and that the two
leads are correctly fixed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or
.
For 115 V units with a power rating exceeding 1500
W, we recommend to fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor size
is 1.5 mm
2
. When using a cable reel, always unwind
the cable completely. Also refer to the table below.
Conductor size (mm
2
)
Cable rating (Amperes)
0.75
6
1.00
10
1.50
15
2.50
20
4.00
25
Cable length (m)
7.5
15
25
30
45
60
Voltage
Amperes
Cable rating (Amperes)
115
0 - 2.0
6
6
6
6
6
10
2.1 - 3.4
6
6
6
6
15
15
3.5 - 5.0
6
6
10
15
20
20
5.1 - 7.0
10
10
15
20
20
25
7.1 - 12.0
15
15
20
25
25
-
12.1 - 20.0
20
20
25
-
-
-
230
0 - 2.0
6
6
6
6
6
6
2.1 - 3.4
6
6
6
6
6
6
3.5 - 5.0
6
6
6
6
10
15
5.1 - 7.0
10
10
10
10
15
15
7.1 - 12.0
15
15
15
15
20
20
12.1 - 20.0
20
20
20
20
25
-
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
DW563/DW563KC - Selecting the operating
mode (fig. B)
The Rotary Hammer Drill can be used in two
operating modes:
Rotary drilling:
for screwdriving, drilling into steel, wood
and plastics
Hammer drilling:
simultaneous rotating and impacting for
concrete and masonry drilling
DW566K/DW566KC - Selecting the operating
mode (fig. B)
The Rotary Hammer Drill can be used in three
operating modes:
Rotary drilling:
for screwdriving, drilling into steel, wood
and plastics
Hammer drilling:
simultaneous rotating and impacting for
concrete and masonry drilling
Hammering only with spindle lock:
impacting only - for light chipping,
chiselling and demolition applications.
• Select the required operating mode by rotating
the mode selector (4) towards the symbol on the
gear housing.
• For screwdriving, refer to section “Instructions for
use”.
Inserting and removing SDS-plus
®
accessories
(fig. C)
Your Rotary Hammer Drill uses SDS-plus
®
accessories (refer to the inset in fig. C for a cross-
section of an SDS-plus
®
bit shank).
• Clean and grease the bit shank.
• Insert the bit shank into the tool holder (8).
Содержание DW563
