DeWalt DW030PL-KR, Руководство пользователя

Страница: 9 / 24

KR
9
KR
9
목차
•
사용자 안전
•
배터리 안전
•
설치
•
조작
•
품질 보증
•
오류 코드
•
사양
향후 참고할 수 있도록 모든 설명서를 보관해 두
십시오.
사용자 안전
경고:
본 제품을 사용하기 전에 안전 지침과 제
품 설명서를 주의 깊게 읽고 숙지하십시
오
.
제품의 책임자는 모든 사용자가 이러
한 설명서와 지침 사항을 이해하고 충실
히 지키는지 확인할 의무가 있습니다
.
경고:
사용자의 안전과 편의를 위해 레이저
등급을 알려 주기 위해 다음과 같은
라벨 정보가 레이저 공구에 부착되어
있습니다
.
Contents
• User Safety
• Battery Safety
• Setup
• Operation
• Warranty
• Error Codes
• Specifications
Retain all sections of this manual for future reference.
User Safety
WARNING:
Carefully read the Safety Instructions and
Product Manual before using this product. The
person responsible for the product must ensure
that all users understand and adhere to these
instructions.
WARNING:
The following label information is placed on your
laser tool to inform you of the laser class for your
convenience and safety.
The DW030PL-XJ tool emits a visible laser beam, as
shown in Figure
A
#1. The laser beam emitted is Laser
Class 2 per IEC 60825-1 and complies with 21 CFR
1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007.
WARNING:
While the laser tool is in operation, be careful not
to expose your eyes to the emitting laser beam
(red light source). Exposure to a laser beam
for an extended time period may be hazardous
to your eyes. Do not look into the beam with
optical aids.
WARNING: To reduce the risk of injury, the user
must read the product User Manual and the
Safety Manual.
Setup
Attaching the Wrist Strap
1.
While facing the front of the tool, insert the thin end of
the wrist strap through one of the holes in the lower
right corner of the tool.
2. Push the thin end of the wrist strap until it goes
through the other hole.
3. Separate the two wires, which make up the thin end
of the wrist strap, to form a loop.
4. Insert the thick end of the wrist strap all the way
through the loop in the thin end, so the wrist strap is
securely fastened to the tool (Figure
B
).
Charging the Battery
Fully charge the battery before initial use and whenever
the tool has not been used for 6 months or longer.
1. Locate the port cover on the side of the tool (Figure
A
#4).
2. Using your finger, gently pull the port cover down
(Figure
E
#1).
3. Insert the small end of the USB Recharge Cable into
the port on the side of the tool, making sure to insert
the flat side of the cable into the flat side of the port
(Figure
E
#2).
4. Insert the USB end of the cable into a USB port in
a computer or USB power outlet (Figure
E
#3).
5. Wait approximately 2.5 hours for the battery to fully
charge and then disconnect the USB Recharge
Cable.
DW030PL
-
XJ
공구는 그림
A
#
1
과 같이 가시 레
이저 빔을 방출합니다
.
방출되는 레이저 빔은 레
이저
2
등급 (
IEC 60825
-
1
) 이고
2007
년
6
월
24
일
자의 레이저 고지 번호
50
에 의한 예외 사항을 제
외하고
21 CFR 1040.10
및
1040.11
을 준수합니다
.
경고:
레이저 공구가 작동 중일 때는 방출되고
있는 레이저 빔 (적색 광원) 에 눈이 노
출되지 않도록 주의하십시오
.
장기간 레
이저 빔에 노출되면 눈에 유해할 수 있습
니다
.
광학 보조 기구로 빔을 들여다보지
마십시오
.
Contents
• User Safety
• Battery Safety
• Setup
• Operation
• Warranty
• Error Codes
• Specifications
Retain all sections of this manual for future reference.
User Safety
WARNING:
Carefully read the Safety Instructions and
Product Manual before using this product. The
person responsible for the product must ensure
that all users understand and adhere to these
instructions.
WARNING:
The following label information is placed on your
laser tool to inform you of the laser class for your
convenience and safety.
The DW030PL-XJ tool emits a visible laser beam, as
shown in Figure
A
#1. The laser beam emitted is Laser
Class 2 per IEC 60825-1 and complies with 21 CFR
1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007.
WARNING:
While the laser tool is in operation, be careful not
to expose your eyes to the emitting laser beam
(red light source). Exposure to a laser beam
for an extended time period may be hazardous
to your eyes. Do not look into the beam with
optical aids.
WARNING: To reduce the risk of injury, the user
must read the product User Manual and the
Safety Manual.
Setup
Attaching the Wrist Strap
1. While facing the front of the tool, insert the thin end of
the wrist strap through one of the holes in the lower
right corner of the tool.
2.
Push the thin end of the wrist strap until it goes
through the other hole.
3. Separate the two wires, which make up the thin end
of the wrist strap, to form a loop.
4.
Insert the thick end of the wrist strap all the way
through the loop in the thin end, so the wrist strap is
securely fastened to the tool (Figure
B
).
Charging the Battery
Fully charge the battery before initial use and whenever
the tool has not been used for 6 months or longer.
1.
Locate the port cover on the side of the tool (Figure
A
#4).
2. Using your finger, gently pull the port cover down
(Figure
E
#1).
3. Insert the small end of the USB Recharge Cable into
the port on the side of the tool, making sure to insert
the flat side of the cable into the flat side of the port
(Figure
E
#2).
4.
Insert the USB end of the cable into a USB port in
a computer or USB power outlet (Figure
E
#3).
5. Wait approximately 2.5 hours for the battery to fully
charge and then disconnect the USB Recharge
Cable.
Contents
• User Safety
• Battery Safety
• Setup
• Operation
• Warranty
• Error Codes
• Specifications
Retain all sections of this manual for future reference.
User Safety
WARNING:
Carefully read the Safety Instructions and
Product Manual before using this product. The
person responsible for the product must ensure
that all users understand and adhere to these
instructions.
WARNING:
The following label information is placed on your
laser tool to inform you of the laser class for your
convenience and safety.
The DW030PL-XJ tool emits a visible laser beam, as
shown in Figure
A
#1. The laser beam emitted is Laser
Class 2 per IEC 60825-1 and complies with 21 CFR
1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007.
WARNING:
While the laser tool is in operation, be careful not
to expose your eyes to the emitting laser beam
(red light source). Exposure to a laser beam
for an extended time period may be hazardous
to your eyes. Do not look into the beam with
optical aids.
WARNING: To reduce the risk of injury, the user
must read the product User Manual and the
Safety Manual.
Setup
Attaching the Wrist Strap
1. While facing the front of the tool, insert the thin end of
the wrist strap through one of the holes in the lower
right corner of the tool.
2. Push the thin end of the wrist strap until it goes
through the other hole.
3. Separate the two wires, which make up the thin end
of the wrist strap, to form a loop.
4. Insert the thick end of the wrist strap all the way
through the loop in the thin end, so the wrist strap is
securely fastened to the tool (Figure
B
).
Charging the Battery
Fully charge the battery before initial use and whenever
the tool has not been used for 6 months or longer.
1. Locate the port cover on the side of the tool (Figure
A
#4).
2. Using your finger, gently pull the port cover down
(Figure
E
#1).
3.
Insert the small end of the USB Recharge Cable into
the port on the side of the tool, making sure to insert
the flat side of the cable into the flat side of the port
(Figure
E
#2).
4. Insert the USB end of the cable into a USB port in
a computer or USB power outlet (Figure
E
#3).
5. Wait approximately 2.5 hours for the battery to fully
charge and then disconnect the USB Recharge
Cable.
Contents
• User Safety
• Battery Safety
• Setup
• Operation
• Warranty
• Error Codes
• Specifications
Retain all sections of this manual for future reference.
User Safety
WARNING:
Carefully read the Safety Instructions and
Product Manual before using this product. The
person responsible for the product must ensure
that all users understand and adhere to these
instructions.
WARNING:
The following label information is placed on your
laser tool to inform you of the laser class for your
convenience and safety.
The DW030PL-XJ tool emits a visible laser beam, as
shown in Figure
A
#1. The laser beam emitted is Laser
Class 2 per IEC 60825-1 and complies with 21 CFR
1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007.
WARNING:
While the laser tool is in operation, be careful not
to expose your eyes to the emitting laser beam
(red light source). Exposure to a laser beam
for an extended time period may be hazardous
to your eyes. Do not look into the beam with
optical aids.
WARNING: To reduce the risk of injury, the user
must read the product User Manual and the
Safety Manual.
Setup
Attaching the Wrist Strap
1. While facing the front of the tool, insert the thin end of
the wrist strap through one of the holes in the lower
right corner of the tool.
2. Push the thin end of the wrist strap until it goes
through the other hole.
3. Separate the two wires, which make up the thin end
of the wrist strap, to form a loop.
4. Insert the thick end of the wrist strap all the way
through the loop in the thin end, so the wrist strap is
securely fastened to the tool (Figure
B
).
Charging the Battery
Fully charge the battery before initial use and whenever
the tool has not been used for 6 months or longer.
1.
Locate the port cover on the side of the tool (Figure
A
#4).
2. Using your finger, gently pull the port cover down
(Figure
E
#1).
3. Insert the small end of the USB Recharge Cable into
the port on the side of the tool, making sure to insert
the flat side of the cable into the flat side of the port
(Figure
E
#2).
4.
Insert the USB end of the cable into a USB port in
a computer or USB power outlet (Figure
E
#3).
5. Wait approximately 2.5 hours for the battery to fully
charge and then disconnect the USB Recharge
Cable.
경고:
부상 위험을 줄이려면 사용자는 사용 설
명서와 안전 설명서를 주의 깊게 읽어야
합니다
.
설치
손목끈 부착
1. 공구의 앞쪽을 향한 상태에서, 손목끈의 얇은
쪽 끝을 구멍 중 하나를 통해 공구의 하단 오
른쪽 모서리에 끼웁니다
.
2.
다른 구멍을 통과할 때까지 손목끈의 얇은
쪽 끝을 밀어 넣습니다
.
3.
손목끈의 얇은 쪽 끝을 구성하는 두 개의 전
선을 분리해서 고리를 만듭니다
.
4. 고리를 통해 손목끈의 두꺼운 쪽을 얇은 쪽
에 끼워 넣어서, 손목끈이 공구에 단단히 부
착되도록 합니다 (그림
B
).
배터리 충전
처음 사용하기 전과 공구를
6
개월 이상 동안
사용하지 않을 때마다 배터리를 완전히
충전하십시오
.
1.
공구 측면에 있는 포트 커버의 위치를 찾습
니다 (그림
A
#
4
)
.
2.
손가락을 사용해서 포트 커버를 아래로 살짝
내립니다 (그림
E #1).
3.
USB
재충전 케이블의 작은 쪽 끝을 공구의
측면 포트에 끼우고, 케이블의 평평한 쪽이
포트의 평평한 쪽에 끼워졌는지 확인하십시
오 (그림
E
#
2
)
.
4. 케이블의
USB
끝을 컴퓨터의
USB
포트 또는
USB
전원 콘센트에 끼웁니다(그림
E
#
3
)
.
5. 배터리 완충까지 대략
2
시간
30
분 정도 소요
됩니다
.
공구가 켜지면, 배터리 용량이 디스플레이 창에
표시됩니다다 (그림
D #
1
)
.
Contents
• User Safety
• Battery Safety
• Setup
• Operation
• Warranty
• Error Codes
• Specifications
Retain all sections of this manual for future reference.
User Safety
WARNING:
Carefully read the Safety Instructions and
Product Manual before using this product. The
person responsible for the product must ensure
that all users understand and adhere to these
instructions.
WARNING:
The following label information is placed on your
laser tool to inform you of the laser class for your
convenience and safety.
The DW030PL-XJ tool emits a visible laser beam, as
shown in Figure
A
#1. The laser beam emitted is Laser
Class 2 per IEC 60825-1 and complies with 21 CFR
1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007.
WARNING:
While the laser tool is in operation, be careful not
to expose your eyes to the emitting laser beam
(red light source). Exposure to a laser beam
for an extended time period may be hazardous
to your eyes. Do not look into the beam with
optical aids.
WARNING: To reduce the risk of injury, the user
must read the product User Manual and the
Safety Manual.
Setup
Attaching the Wrist Strap
1. While facing the front of the tool, insert the thin end of
the wrist strap through one of the holes in the lower
right corner of the tool.
2. Push the thin end of the wrist strap until it goes
through the other hole.
3. Separate the two wires, which make up the thin end
of the wrist strap, to form a loop.
4. Insert the thick end of the wrist strap all the way
through the loop in the thin end, so the wrist strap is
securely fastened to the tool (Figure
B
).
Charging the Battery
Fully charge the battery before initial use and whenever
the tool has not been used for 6 months or longer.
1. Locate the port cover on the side of the tool (Figure
A
#4).
2. Using your finger, gently pull the port cover down
(Figure
E
#1).
3.
Insert the small end of the USB Recharge Cable into
the port on the side of the tool, making sure to insert
the flat side of the cable into the flat side of the port
(Figure
E
#2).
4. Insert the USB end of the cable into a USB port in
a computer or USB power outlet (Figure
E
#3).
5. Wait approximately 2.5 hours for the battery to fully
charge and then disconnect the USB Recharge
Cable.