DeWalt DE2000, Инструкция по эксплуатации

Страница: 30 / 104

en - 7 22
E N G L I S H
Edge trimming (rebating) and profile cutting (fig. A3 & I)
• Install the appropriate cutter and set the router to the appropriate
depth of cut using the fine height adjustment of the router.
• Check that the appropriate cutting insert (32) is mounted.
• Mount the router fence (29) onto the table and slide it to the middle of
the cutter.
• Loosen the star knobs (7), position the faces (40) as close to the bit as
possible and tighten the star knobs.
The side of the material which will be trimmed must be guided
along the router fence.
• Use the fine adjuster for positioning the router fence in relation to the
expected width of cut.
• Slide the cutter guard (30) to the correct position.
• Press the workpiece against the fence and the table top. When using
the optional down hold guards (DE2007 & DE2008), install them as
described in the section “Horizontal down hold guard (DE2007) and
vertical down hold guard (DE2008) (fig. M3)”.
• Switch the combi-table on.
• Feed the material at an even speed and make the cut in one smooth
pass. The correct feed speed is a matter of experience: too low speed
will produce burn marks on the wood, whereas too high speed will
overload your router.
• When the cut is completed, switch the combi-table off immediately.
Cutting grooves (fig. L)
• Install the appropriate cutter.
• Check that the appropriate cutting insert is mounted.
• Mount the router fence (29) onto the table and slide it to the required
position.
• Slide the faces (40) towards each other to close the gap.
• Proceed as for edge trimming and profile cutting.
Optional accessories (fig. M1 - M3)
DE3000
Conversion kit “Router” DE3011
The conversion kit “Router” converts your DE3000 combi-table into a
complete router table, with all the features and benefits of the DE2000.
The conversion kit contains:
1 Router mounting plate
3 Fixing screws
1 Router fence with dust spout
1 Cutter guard
4 Cutting inserts (Router)
For installation and applications, read the DE2000 sections in this
instruction manual.
DE2000
Conversion kit “Saw” DE2011
The conversion kit “Saw” converts your DE2000 combi-table into a
complete Saw table, with all the features and benefits of the DE3000.
The conversion kit contains:
1 Saw mounting plate incl. mounting device
1 Parallel rip fence
1 Mitre fence
4 Cutting inserts (saw)
1 Saw blade guard with bracket
1 Push stick
1 Mounting device for DW365
1 Switch lock
For installation and applications, read the sections DE3000 in this
instruction manual.
Horizontal down hold guard (DE2007) and vertical down hold guard
(DE2008) (fig. M1)
The down hold guards (82 & 83) are very useful for professional routing.
A down hold guard ensures constant pressure to the workpiece against
the table top and the fence.
Assembling and mounting the vertical down hold guard
• Loosen the three Allen screws (84) on the down hold bracket (85).
• Slide the bracket onto the router fence (29 in fig. A3) up to the dust
spout (33 in fig. A3).
• Mount the down hold guard (82) onto the bracket (85).
• Tighten the three Allen screws (84) securely. The down hold bracket
can be left on the router fence, also when using the cutter guard.
• Loosen the screw (86) and remove the down hold guard.
Mounting the horizontal down hold guard
• Loosen the knobs (87).
• Slide the horizontal down hold guard (83) in the groove (15 in fig. A1).
• Position the horizontal down hold guard where the cutter contacts the
workpiece.
• Tighten the knobs (87).
Using the down hold guards
• Without turning the machine on, feed the workpiece until it touches
the cutter.
• Press the positioned down hold guards onto the workpiece until the
internal spring presses the material against the table and the fence.
Copy follower (DE2009) (fig. M2 & M3)
The copy follower (88) allows the user to work without the router fence
(freehand routing).
The copy set contains:
1 Copy follower with guard and brushes
1 Thrust block (89)
Mounting the copy follower
• Remove the router fence.
• Slide the arm (90) of the copy follower (88) and the thrust block (89)
into the right-hand groove (15 in fig. A1).
• Put the ball bearing guide (91) in the correct position on top of the
cutter. Refer to fig. M3.
• Tighten all knobs securely.
The thrust block (89) ensures your workpiece is always guided to the
correct side of the cutter.
When edge moulding
• Mount the copy follower bearing off-centre to the cutter.
• Make the cut where the widest part of the cutter is exposed.
• Set the tip of the thrust block at a tangent to the cutting point.
• Ensure that the arm and the thrust block knobs are fully tightened.
• With the router off, move your workpiece in the desired manner,
to make sure that all points can be moulded as required.
• Switch the combi-table on and proceed in the usual way.