DeWalt DCS692, Инструкция по эксплуатации, Страница: 14 / 52

English
12
D
e
WALT Bluetooth® Tool Tag Ready (Fig. A)
Optional Accessory
WARNING: Read instruction manual for the D
e
WALT
Bluetooth ® Tool Tag.
WARNING: Remove battery from tool before installing
the D
e
WALT Bluetooth ® Tool Tag.
WARNING: When installing or replacing the D
e
WALT
Bluetooth ® Tool Tag, use only the screws provided. Be
sure to securely tighten the screws.
Your tool comes with mounting holes 15 and fasteners 27
for installing a D
e
WALT Bluetooth ® Tool Tag (DCE041). You
will need a T15 torx bit tip to install the tag. Screw torque
should be between 0.8 and 1.2 Nm (7.1 to 10.6 in‑lbs). The
D
e
WALT Tool Tag is designed for tracking and locating
professional power tools, equipment, and machines using
Adjusting the Guard Angle (Fig. E)
WARNING: Do not use guard rotation handle to
hold tool while cutting. Guard rotation handle is
only used for adjustment of the guard while tool is not
in use.
CAUTION: Guard may be hot. Use guard handle to
rotate guard.
WARNING: Always make sure the guard is properly
engaged before starting the machine.
You can adjust the angle of the guard.
1. To adjust the angle of the guard, pull back the guard
rotation release lever 14 and hold it.
2. Grasp the guard
9
firmly by guard rotation handle
10
and rotate to desired angle.
3. Release the guard rotation release lever and make sure it
engages, locking the guard in place. If the guard rotation
release lever doesn't engage, rotate the guard slightly
until the guard rotation release lever returns to the
locked position.
Replacing Worn Clamp Washers (Fig. D)
WARNING: Replace clamp washers as they wear. They
may become sharp with extended use.
1. Remove the arbor screw 11 , outer clamp washer 21
and used wheel
22
if one is installed as described in
Installing Abrasive and Diamond Wheels.
2. To remove the inner clamp washer 23 , first remove the
retaining ring that holds the inner clamp washer to the
double D shaft.
3. Remove the inner clamp washer and replace with a new
one. Orient the inner clamp washer with the depressed
center section toward the blade. Make sure the new
inner clamp washer is secure with the retaining ring
in place.
4. Install the wheel 22 , new outer clamp washer 21 , and
arbor screw 11 as described in Installing Abrasive and
Diamond Wheels.
CAUTION: Only use 9" (230 mm) Type 1/41 wheels
with 7/8" (22.2 mm) arbor hole with this tool. Never
force a wheel onto the machine or alter the size of the
arbor hole.
Installing Abrasive and Diamond Wheels
(Fig. A, D)
WARNING: Install only one blade.
1. Lay unit on a firm surface, with the arbor screw
11
facing upward.
2. Using supplied 1/2" (13 mm) open end wrench 6
(located in the battery compartment), remove arbor
screw
11 , outer clamp washer 21 and used wheel 22
if one is installed. Hold arbor screw 11 from turning with
spindle lock button
13
. Spindle threads are right hand.
3. The inner clamp washer 23 is held in place with a
double D shaft and retaining ring.
4. Slip wheel over spindle 25 . Slip on outer clamp washer.
Start threading on arbor screw which will self align outer
clamp washer.
iMPORTAnT: Make sure the diamond blade is installed
with the correct rotation, as marked on the blade rotation
indicator
12 .
5. Engage spindle lock button and tighten screw firmly with
wrench. Do not over‑tighten arbor screw.
6. Turn wheel by hand to ensure it is properly centered. The
wheel should not hit the shoe or guard. The screw and
flanges should be tight.
Spindle Lock Button (Fig. A)
The spindle lock button 13 is used to lock the arbor
screw 11 when changing accessories.
1. To engage the spindle lock button, remove the battery
pack and make sure trigger switch is in the OFF position
and lock‑off button is engaged.
2. Depress the spindle lock button and turn the wheel and
spindle until the lock button engages the spindle.
3. Use supplied wrench 6 to unscrew the arbor screw 11
and remove or mount accessories. Spindle threads are
right hand.
Lock‑Off Button (Fig. A)
Your cut‑off tool is equipped with a lock‑off button 3 .
To lock the trigger switch in the OFF postition, push the
lock‑off button from the left side of the tool. To unlock the
trigger switch, push the lock‑off button from the right side
of the tool.
SPECIFICATIONS
DCs692
Blade diameter 9" (230 mm)
Arbor size 7/8" (22.2 mm)
RPM 6600
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start‑up can cause injury.