DeWalt DCS571, Руководство пользователя

Страница: 40 / 172

38
EnGLIsh
Fuel Gauge Battery Packs (Fig. B)
Some D
e
WALT battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button
16
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE:
The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Installing the Belt Hook (Fig. C)
WARNING: To reduce the risk of serious personal
injury, ONLY use the tool’s belt hook to hang the tool
from a work belt. DO NOT
use the belt hook for tethering
or securing the tool to a person or object during use.
DO
NOT
suspend tool overhead or suspend objects from the
belt hook.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
IMPORTanT:
When attaching or replacing the belt hook
19
,
use only the screw 20 that is provided. Be sure to securely
tighten the screw.
If the hook is not desired at all, it can be removed from the tool.
Trigger Switch (Fig. A)
WARNING:
This tool has no provision to lock the trigger
switch in the ON position and should never be locked ON
by any other means.
Release the trigger switch lock‑off button
1
by pressing the
button. Pull the trigger switch 2 to turn the motor on. Releasing
the trigger switch turns the motor off.
Depth of Cut Adjustment (Fig. D)
1. Loosen the depth adjustment lever 4 .
2. Move the shoe
5
to obtain the correct depth of cut.
3. Tighten the depth adjustment lever 4 .
4. For the most efficient cutting action using a carbide tipped
saw blade, set the depth adjustment so that about one half
of a tooth projects below the surface of the wood to be cut.
nOTE:
A method of checking for the correct cutting depth
is shown in the inset in Figure D. Lay a piece of the material
you plan to cut along the side of the blade and observe how
much tooth projects beyond the material.
Bevel Adjustment (Fig. E)
The bevel angle can be adjusted between 0 ° and 45 °.
1. Loosen the bevel adjustment knob 10 .
2. Set the bevel angle by tilting the saw shoe
5
until the mark
indicates the desired angle on the scale.
3. Tighten the bevel adjustment knob
10
.
Shoe Adjustment for 90 ° Cuts (Fig. A, D, E)
1. Adjust the saw to 0 ° bevel.
2. Retract the blade guard using the lever
6
and place the saw
on the blade side.
3. Loosen the bevel adjustment knob
10
.
4. Place a square against the blade and shoe to adjust the
90 ° setting.
5. Turn the calibration screw 29 so that the shoe will stop at
the proper angle.
6. Confirm the accuracy of the setting by checking the
squareness of an actual cut on a scrap piece of material.
Rip Guide Installation and Usage (Fig. A, F)
Ripping is the process of cutting wider boards into narrow
strips, cutting the grain lengthways. Hand guiding is more
difficult for this type of sawing and the use of the rip guide
is recommended.
WARNING:
For your own safety, read the instruction
manual before using any accessory. Failure to heed
these warnings may result in personal injury and serious
damage to the saw and accessory. When servicing this
tool, only use identical replacements.
Assembly
1. Loosen the rip fence guide locking screw 27 with the hex
key
14
.
2. Insert the rip guide 30 as shown in Figure F.
3. Tighten the rip fence guide locking screw
27
securely.
Use the supplied rip guide only with the DCS571 circular
saw. Use of this rip guide with other saws may increase the risk
of kickback and injury.
Before making a cut, ensure the rip fence is securely fastened
to the tool.
After installing the rip guide on the saw or after moving the
guide to change the rip width setting, check the operation
of the lower guard before starting the saw and making a
cut to make sure that the rip guide does not affect proper
guard operation.
Replacing the Saw Blade (Fig. A, G)
1. Engage the blade lock button
11
and unscrew the blade
clamping screw
8
by turning clockwise using the hex key
supplied with the tool.
2. Retract the lower blade guard
7
using the lever
6
and
replace the blade. Reinstall the washers ( 17 , 18 ) in the
correct position.
3. Check the direction of rotation of the blade.
4. Thread on the blade clamping screw
8
by hand to hold the
washer in position. Turn counterclockwise.
5. Press the blade lock button
11
while turning the spindle
until the blade stops rotating.
6. Tighten the blade clamping screw firmly using the hex key.