background image

MAINTENANCE

 

WARNING: To reduce the risk of serious personal injury, 

lock the trigger switch and disconnect battery pack before 
making any adjustments or removing/installing attachments 
or accessories.

 An accidental start-up can cause injury.

Cleaning

 WARNING:

 Blow dirt and dust out of all air vents with clean, dry air 

at least once a week. To minimize the risk of eye injury, always wear 

ANSI Z87.1 approved eye protection when performing this. 

 WARNING:

 Never use solvents or other harsh chemicals for 

cleaning the non-metallic parts of the tool. These chemicals may 
weaken the plastic materials used in these parts. Use a cloth 
dampened only with water and mild soap. Never let any liquid get 
inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

 WARNING: 

Shock hazard. Disconnect the charger from the AC 

outlet before cleaning. Dirt and grease may be removed from the 
exterior of the charger using a cloth or soft non-metallic brush. Do not 
use water or any cleaning solutions.

Accessories

 WARNING: 

Since accessories, other than those offered by 

D

E

WALT, have not been tested with this product, use of such 

accessories with this tool could be hazardous. To reduce the risk of 
injury, only D

E

WALT recommended accessories should be used with 

this product. 

Recommended accessories for use with your tool are available 
at extra cost from your local dealer or authorized service center. If 
you need assistance in locating any accessory, please contact 
D

E

WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 

21286, call 1-800-4-D

E

WALT (1-800-433-9258) or visit our website 

www.dewalt.com.

Repairs

The charger and battery pack are not serviceable. There are no 

serviceable parts inside the charger or battery pack. 

To assure product SAFETY and RELIABILITY, repairs, maintenance 

and adjustment (including brush inspection and replacement) should 
be performed by a D

E

WALT factory service center, a D

E

WALT 

authorized service center or other qualified service personnel. Always 
use identical replacement parts.

Three Year Limited Warranty

D

E

WALT will repair, without charge, any defects due to faulty materials 

or workmanship for three years from the date of purchase. This 
warranty does not cover part failure due to normal wear or tool 
abuse. For further detail of warranty coverage and warranty repair 
information, visit www.dewalt.com or call 1-800-4-D

E

WALT (1-800-

433-9258). This warranty does not apply to accessories or damage 

caused where repairs have been made or attempted by others. This 
warranty gives you specific legal rights and you may have other rights 
which vary in certain states or provinces.

In addition to the warranty, D

E

WALT tools are covered by our:

1 YEAR FREE SERVICE

D

E

WALT will maintain the tool and replace worn parts caused by 

normal use, for free, any time during the first year after purchase.

2 YEARS FREE SERVICE ON D

E

WALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180, DCB120 

and DCB201

 

3 YEARS FREE SERVICE ON D

E

WALT BATTERY PACKS

DCB200

English

14

Содержание DCS310S1

















Отзывы: