DeWalt DCMWSP255, Инструкция по эксплуатации

Страница: 18 / 52

English
16
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
•
COnFiRMATiOn OF OWnERshiP:
In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof of purchase.
•
FOR YOUR sAFETY:
Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
• Register online at
www.dewalt.com
.
Repairs
The charger and battery pack are not serviceable. There are
no serviceable parts inside the charger or battery pack.
WARNING:
To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a
D
e
WALT factory service center or a
D
e
WALT authorized service center. Always use identical
replacement parts.
Accessories
WARNING:
Since accessories, other than those offered
by D
e
WALT , have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
D
e
WALT recommended
accessories should be used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact
D
e
WALT call 1‑800‑4‑ D
e
WALT
(
1‑800‑433‑9258
) or visit our website:
www.dewalt.com
.
Meets CPSC Safety Requirements
D
e
WALT Mowers conform to the safety standards of
the American National Standards Institute, and the U.S.
Consumer Product Safety Commission. The blade turns when
the blade motor is running.
Corrosion (Fig. A)
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals. If you mow in areas
where fertilizers or chemicals have been used, the mower
should be cleaned immediately afterward as follows:
Release bail handle
5 to turn mower off and remove battery
and safety key. Wipe all exposed parts with a damp cloth.
CAUTION: Do not pour or spray water on the mower
in an attempt to clean it. Do not store the tool on or
adjacent to fertilizers or chemicals. Such storage can
cause rapid corrosion.
Cleaning (Fig. A)
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always use ANSI Z87.1 (CAN/CSA Z94.3)
approved eye protection and NIOSH/OSHA/MSHA
approved respiratory protection when performing this.
WARNING:
Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Release bail handle 5 to turn mower off, let the blade come
to a stop and then remove the battery packs and safety key.
Clean out any clippings which may have accumulated on the
underside of the deck. Do not spray water or other liquids.
After several uses, check all exposed fasteners for tightness.
Blade Balancing (Fig. S)
Check balance of the blade 33 by placing center hole in
the blade over a nail or round screwdriver 37 , clamped
horizontally in a vise 35 . If either end of the blade rotates
downward, file along the sharp edge of that dropping end.
Blade is properly balanced when neither end drops.
Blade Sharpening
KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A
DULL BLADE DOES NOT CUT GRASS CLEANLY.
WARNING: Use gloves and proper eye protection while
removing, sharpening, and installing blade. Ensure that
safety key and battery pack are removed.
Sharpening the blade twice during a mowing season is
usually sufficient under normal circumstances. Sand causes
the blade to dull quickly. If your lawn has sandy soil, more
frequent sharpening may be required.
REPlACE BEnT OR
DAMAgED BlADE iMMEDiATElY.
When Sharpening the Blade:
• Make sure blade remains balanced.
• Sharpen blade at the original cutting angle.
• Sharpen cutting edges on both ends of blade, removing
equal amounts of material from both ends.
To Sharpen Blade in a Vise (Fig. R)
1. Be sure the bail handle is released, the blade has stopped
and safety key and battery packs are removed before
removing the blade.
2. Remove blade from mower. See instructions for
Removing and Installing Blade
.
3. Secure blade 33 in a vise 35 .
4. Wear proper eye protection and gloves and be careful
not to cut yourself.
5. Carefully file the cutting edges of the blade with a
fine tooth file 36 (not included) or sharpening stone
(not included), maintaining the angle of the original
cutting edge.
6. Check balance of blade. See instructions for Blade Balancing .
7. Replace blade on mower and tighten securely.