36
english
Belt Hook and Bit Clip (Fig. 1)
WARNING: To reduce the risk of
serious personal injury, DO NOT
suspend tool overhead or suspend
objects from the belt hook.
ONLY
hang
tool’s belt hook from a work belt.
WARNING: To reduce the risk of
serious personal injury,
ensure the
screw holding the belt hook is secure.
IMPORTANT:
When attaching or replacing the
belt hook or bit clip, use only the screw (I) that is
provided. Be sure to securely tighten the screw.
The belt hook (H) and bit clip (J) can be be attached
to either side of the tool using only the screw (I)
provided, to accommodate left- or right-handed
users. If the hook or bit clip is not desired at all, it
can be removed from the tool.
To move belt hook or bit clip, remove the screw
(I) that holds it in place then reassemble on the
opposite side. Be sure to securely tighten the screw.
OPERATION
Instructions for Use
WARNING:
Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
An accidental start-up can
cause injury.
Proper Hand Position (Fig. 1, 4)
WARNING:
To reduce the risk of serious
personal injury,
ALWAYS
use proper
hand position as shown.
WARNING:
To reduce the risk of serious
personal injury,
ALWAYS
hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the main
handle (K).
Variable Speed Trigger Switch
(Fig. 1)
To turn the tool on, squeeze the trigger switch (A).
To turn the tool off, release the trigger switch. Your
tool is equipped with a brake. The chuck will stop
when the trigger switch is fully released.
(see
Technical Data
). The minimum conductor size
is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
An accidental start-up can
cause injury.
WARNING:
Use only
D
e
WALT
battery
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (Fig. 2)
NOTE:
Make sure your battery pack (F) is fully
charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack (F) with the rails inside
the tool’s handle (Fig. 2).
2. Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that you
hear the lock snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release button (E) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 2)
Some
D
e
WALT
battery packs include a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (L). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE:
The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Содержание DCF836
