background image

ENGLISH

26

Additional Safety Instructions for 

Battery Packs

When using the charger, always observe the safety 

regulations applicable in your country to reduce the 

risk of fire, electric shock and personal injury. Read 

the following safety instructions before attempting 

to operate this product. Keep these instructions in a 

safe place.
This charger is in accordance with the relevant safety 

regulations. To avoid danger, electric appliances 

must only be repaired by qualified technicians.

 

  

WARNING: 

Fire hazard! Avoid metal 

short circuiting the contacts of a 
detached battery pack. Do not store 
or carry the battery pack without the 
battery cap placed over the contacts.

  •  The battery fluid, a 25-30% solution of 

potassium hydroxide, can be harmful. In case 
of skin contact, flush immediately with water. 
Neutralize with a mild acid such as lemon 
juice or vinegar. In case of eye contact, rinse 
abundantly with clean water for at least 10 
minutes. Consult a physician.

  •  Never attempt to open a battery pack for 

any reason.

Additional Safety Instructions 

for Chargers

  •  Make sure that the battery pack is dry and 

clean before inserting it into the charger.

  •  Use only chargers labelled “NiMH” or “NiMH + 

NiCd” to charge D

E

WALT NiMH battery packs.

  •  Never carry the charger by its cord. Keep the 

cord away from heat, oil and sharp edges.

  •  Do not attempt to charge wet battery packs.
  •  Always follow the instructions in the back of this 

manual for battery pack disposal.

  •  When not in use, chargers and battery packs 

must be stored in a dry place and locked up 
securely, out of reach of children

LABELS ON CHARGER AND BATTERY PACK

In addition to the pictographs used in this manual, 

the labels on the charger and the battery pack show 

the following pictographs:

 Battery charging

 Battery charged

 Battery defective

 Hot\cold pack delay

  Do not probe with conductive objects.

   Do not charge damaged battery packs

   Read instruction manual 

before use.

 

 Use only with D

E

WALT battery packs, 

others may burst, causing personal injury 

and damage.

   Do not expose to water. 

   Have defective cords replaced 

immediately.

 

Charge only between 4 °C and 40 °C.

   Discard the battery pack with due care for 

the environment.

   Do not incinerate the battery pack NiMH/

NiCd+.

  Charges NiMH and NiCd 

battery packs.

  See technical data for charging time.

 

Lamp location.

  For indoor use. 

  Ensure correct bulb is used.

  Do not plug cord in.

  Correct bulb placement.

  Battery clamp down.

Содержание DC021














Отзывы: