ENGLISH
30
CAUTION:
Cut hazard. If replacing a
broken bulb, protect your hands before
attempting to remove the bulb. Do not
remove any pieces of broken glass
or bulb from the outlet area with bare
hands, or personal injury may occur.
CAUTION: Do not touch bulb
immediately after use.
Allow the bulb
to cool before removing. Contact with a
hot bulb may cause personal injury.
To change the fluorescent bulb, the worklight
housing must be in an upward position as shown in
Figure 2.
NOTE:
Recommended replacement bulb is the
D
E
WALT DC0213 38W fluorescent bulb.
1. With one hand securing the bottom corner of
the worklight housing (j) and lens cover (i), use
the other hand to roll back the rubber gasket
(n) from the worklight housing starting at one
of the top corners.
2. Still securely holding the worklight housing roll
back the rubber gasket from all sides of the
housing (Fig. 5).
3. Remove the rubber gasket and lens cover and
set aside.
4. With one hand securing the bottom corner of
the worklight housing, use the other hand to
remove the bulb guard (o). Gently squeeze the
sides of the bulb guard with the thumb and
index finger to release it from the clips. Set the
bulb guard aside.
5. Secure the bottom corner of the worklight
housing with one hand. Use the other hand
to firmly grasp the fluorescent bulb (h) at the
center and hold onto the white plastic housing
under the bulb guard. While still securing the
bottom corner, gently remove the bulb from the
worklight housing as shown in Figure 6. Ensure
that the outlet and area around the outlet is free
of dirt, dust and other contaminants.
6. Align the replacement fluorescent bulb in the
same orientation as the previous bulb. Secure
the bottom corner of the worklight housing with
one hand. Using the other hand, carefully press
on the center of the bulb’s plastic housing to
secure it in place.
7. Once the replacement bulb is in place, gently
press the center of the bulb’s plastic housing
to ensure it is connected properly. Replace
the bulb guard by clipping it to the worklight
housing.
8. Replace the lens cover. Place the rubber gasket
in one corner and roll the gasket into place on
all four sides of the worklight housing. Ensure
the rubber gasket is firmly in place around the
worklight housing.
MAINTENANCE
Your D
E
WALT appliance has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
from power source
before installing
and removing accessories, before
adjusting or changing set-ups or when
making repairs. Be sure the trigger
switch is in the OFF position. An
accidental start-up can cause injury.
Service Notes
This product is not user serviceable. Other than
the replacement bulb, there are no user
serviceable parts inside the worklight/charger.
Servicing at an authorized service center is
required to avoid damage to static sensitive
internal components.
Cleaning
WARNING:
When cleaning, use only
a damp cloth on plastic parts. Many
household cleaners contain chemicals
which could seriously damage plastic
parts. Also, do not use gasoline,
turpentine, lacquer or paint thinner, dry
cleaning fluids or similar products which
may seriously damage plastic parts.
Never let any liquid get inside the tool;
never immerse any part of the tool into a
liquid.
WORKLIGHT/CHARGER CLEANING INSTRUCTIONS
WARNING:
Disconnect the worklight/
charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the
worklight/charger using a cloth or soft
non-metallic brush. Do not use water
or any cleaning solutions.
Содержание DC021
Страница 1: ...DC021 DC022 www eu ...
Страница 2: ...1 Figure 1 Figure 2 j h i m o n DC022 DC021 a b c e f g d a b c d e f g d d ...
Страница 3: ...2 Figure 3 Figure 4 k l Figure 5 A B DC022 GB DC022 QW ...
Страница 4: ...3 Figure 6 Figure 7 n o h n ...
