23
EngLIsh
WARNING:
We recommend the use of a residual current
device with a residual current rating of 30mA or less.
Residual Risks
• The following risks are inherent to the use of these machines:
ʵ Injuries caused by touching the rotating parts.
ʵ Injuries caused by disruption of the cutting disc.
• These risks are most evident:
ʵ Within the range of operation.
ʵ Within the range of the rotating machine parts.
• In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
ʵ Impairment of hearing.
ʵ Risk of accidents caused by the uncovered parts of the
rotating cutting disc.
ʵ Risk of injury when changing the disc.
ʵ Risk of squeezing fingers when opening the guards.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your
D
e
WALT
tool is double insulated in accordance
with EN61029; therefore no earth wire is required.
WARNING:
115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the
D
e
WALT
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
WARNING:
No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data
).The minimum conductor size is 1.5 mm2; the
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
Connecting to the Mains
The mains supply to be used for this machine must be equipped
with a 16 A cut-out fuse with time delay.
Voltage Drops
Inrush currents cause short-time voltage drops. Under
unfavourable power supply conditions, other equipment may
be affected.
If the system impedance of the power supply is lower than 0.11
ø, disturbances are unlikely to occur.
Package Contents
The package contains:
1 Chopsaw
1 Hex key
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Bore diameter.
Date Code Position (Fig. A)
The date code
21
, which also includes
the year of manufacture,
is printed into the housing.
Example:
2018 XX XX
Year of Manufacture
Description (Fig. A)
WARNING:
Never modify the power tool or any part of it.
Damage or personal injury could result.
1
On/off switch
2
Padlock hole
3
Operating handle
4
Carrying handle
5
Depth stop bolt
6
Lock nut
7
Base
8
Fence
9
Material clamp
10
Cutting table
11
8 mm hex key
12
Handle
13
Material clamp lever
Содержание D28710
