DeWalt D28106-XE Скачать руководство пользователя страница 7

Страница: 7 / 16

ASSEMBLY AND ADJUSTMENTS

Attaching Side Handle

The side handle (E) can be fitted to either side of the gear

case in the threaded holes, as shown. Before using the

tool, check that the handle is tightened securely.

Rotating the Gear Case

WARNING:

Turn off and unplug the tool before making

any adjustments or removing or installing attachments or

accessories.

Before reconnecting the tool, depress and

release the paddle switch to ensure that the tool is off.
1. Remove guard and flanges from tool.
2. Remove the four corner screws attaching the

gear case to motor housing.

3. Separating the gear case from motor housing

not more than 6 mm (1/4"), rotate the gear

case head to desired position.

NOTE:

If the gear case and motor housing

become separated by more than 6 mm (1/4"),

the tool must be serviced and re-assembled by

a D

WALT service center. Failure to have the tool

serviced may cause brush, motor and bearing failure.
3. Re-install screws to attach the gear case to the motor housing. Tighten screws to

2 nm (18 in.lbs.) torque. Overtightening could cause screws to strip.

Accessories

It is important to choose the correct guards, backing pads and flanges to use

with grinder accessories. See pages 7–8 for information on choosing the correct

accessories.

WARNING:

Accessories must be rated for at least the speed recommended on the

tool warning label. Wheels and other accessories running over rated accessory speed

may burst and cause injury. Threaded accessories must have a M14x2 hub. Every

unthreaded accessory must have a 22 mm (7/8") arbor hole. If it does not, it may

D28402-XE

FIG. 1

D28106-XE

D28113-XE

D28130-XE

D28135-XE

D28139-XE

G
H

Содержание D28106-XE

















Результаты поиска

Содержание D28106-XE

Отзывы:

Похожие инструкции для D28106-XE

Бренды по названию

Популярные бренды

DeWalt D28106-XE, Инструкция по эксплуатации

Результаты поиска

Содержание D28106-XE

Отзывы:

Похожие инструкции для D28106-XE

Бренды по названию

Популярные бренды