background image

13

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment 

(including brush inspection and replacement) should be performed by certified 

service centers or other qualified service organizations, always using identical 

replacement parts.

ACCESSORIES

WARNING: 

Since accessories, other than those offered by D

E

WALT, have not been 

tested with this product, use of such accessories with this tool could be hazardous. 

To reduce the risk of injury, only D

E

WALT, recommended accessories should be used 

with this product. 
Recommended accessories for use with your tool are available at extra cost from 

your local service center. If you need any assistance in locating any accessory, 

please contact D

E

WALT Industrial Tool Co., 20 Fletcher Road, Mooroolbark, VIC 3138 

Australia or call 1800 654 155 or (NZ) 0800 339258.

Guarantee

Applicable to hand held Power Tools, Lasers and Nailers.

Three Year Limited Warranty

D

E

WALT will repair, without charge, any defects due to faulty materials or 

workmanship for three years from the date of purchase. Please return the complete 

unit, transportation prepaid, to any D

E

WALT Service Centre, or any authorised 

service station.  
For warranty repair information, call (AUS) 1800 654 155 or (NZ) 0800 339258.
This warranty does not apply to 

• Accessories 
•  Damage caused where repairs have been made or attempted by others. 
•  Damage due to misuse, neglect, wear and tear, alteration or modification.

This warranty gives you specific legal rights and you may have other rights under the 

provisions of the Consumer Guarantee Act 1993 (New Zealand only), Trade Practices 

Act 1974 and State Legislation (Australia only).

In addition to the warranty, D

E

WALT tools are covered by our:

FREE ONE YEAR SERVICE CONTRACT

D

E

WALT will also maintain the tool for free at any time during the first year of 

purchase. This includes labour, parts and lubrication required to restore the product to 

sound mechanical and/or electrical condition. Normal wear parts are not covered in 

this service. Carbon brushes worn more than 50% will be replaced.

NOTE: 

Three Year Warranty is not applicable to items deemed as consumables. Radial 

arm saws are covered by a one (1) year warranty only. D

E

WALT Reserves the right to 

review its warranty policy prior to launch of any new business development products.

30 DAY NO SATISFACTION GUARANTEE

If you are dissatisfied with any D

E

WALT power tool, laser or nailer, for any reason, 

simply return it to the point of purchase with your sales receipt within 30 days for a 

replacement unit or a full refund.

FREE WARNING LABEL REPLACEMENT: 

If your warning labels become illegible or 

are missing, call (AUS) 1800 654 155 or (NZ) 0800 339258 for a free replacement.

Содержание D28106-XE

















Отзывы: