DeWalt D27107, Оригинальное руководство пользователя

Страница: 51 / 180

49
• Fit the items 31 - 38 onto the two guide rails (32 & 33).
• Use the inclinable support (34) for cross-cutting 210 mm wide boards
(15 mm thick).
Roller support table (fi g. A6)
The roller support table (40) is used to support long workpieces. In mitre
saw mode, the roller support table can be mounted on the left-hand side
or on the right-hand side, or with two sets on either side. In saw bench
mode, it can also be mounted in front or at the rear of the saw table.
Side extension table (fi g. A8)
The side extension table (42) increases the distance from the rip fence to
the blade to 600 mm or more, depending on the rod length fi tted to the
machine and the clamped position of the table. The side extension table
must be used in conjunction with guide rails (32) (option). The adjustable
table is equipped with an engraved scale along its front edge and mounted
on a sturdy base which clamps to the guide rods.
• Fit the extension table to the right-hand side of the machine for
continuity of the distance scale on both tables.
Sliding table (fi g. A9)
This sliding table (43) allows for board sizes to the left of the blade up to
1200 x 900 mm.
The guide rods are mounted on a sturdy alloy extrusion which is quickly
detachable from the machine and yet fully adjustable is all planes.
The fence incorporates a full length measuring tape for quick positioning of
an adjustable stop and an adjustable support for narrow workpieces.
Transporting (fi g. X)
WARNING: Always transport the machine in saw bench mode
with the upper blade guard fitted.
The castor wheels provide an easier transport of the machine.
• Put the machine on the right base side.
• Fold the rear legs into the base
• Fold the front legs out of the base
• Turn the machine straight up.
• Lift the machine by the front legs up to the wheels are in contact with
the floor.
WARNING: When carrying the machine, always seek
assistance.
MAINTENANCE
Your D
E
WALT power tool has been designed to operate over a long period
of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing
and removing accessories, before adjusting or changing
set-ups or when making repairs.
Be sure the trigger switch
is in the OFF position. An accidental start-up can cause injury.
Lubrication
The bearings of the motor are pre-lubricated and watertight.
• Slightly oil the rotating table bearing surface where it slides on the lip of
the fi xed table at regular intervals.
• Periodically lubricate the depth of cut screwthread.
• Clean the parts subject to accumulation of sawdust and chips
periodically with a dry brush.
Cam adjustment (fi g. Y1 - Y3)
To take out the clearance between the two tables, proceed as follows:
• Rotate the machine into saw bench mode.
• Remove the screws (138) and the retainer plate (139).
• Loosen the screw (140) of the adjustment cam (141).
• Rotate the adjustment cam using a pair of needle nose pliers.
• Hold the adjustment cam with the pliers and tighten the screw.
• Replace the retainer plate and tighten the screws.
• Rotate the machine into mitre saw mode. Check the force that is
needed to mitre the saw. Repeat the above steps if the force needed is
too high.
Cleaning
Before use, carefully check the upper blade guard, movable lower blade
guard as well as the dust extraction tube to determine that it will operate
properly. Ensure that chips, dust or workpiece particle cannot lead to
blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and guards
disconnect the machine from the power supply and follow the instructions
given in section
Mounting the Saw Blade . Remove the jammed parts and
reassembling the saw blade.
WARNING: Blow dirt and dust out of the main housing with dry
air as often as dirt is seen collecting in and around the air vents.
Wear approved eye protection and approved dust mask when
performing this procedure.
WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals
may weaken the materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool into a
liquid.
WARNING: To reduce the risk of injury, regularly clean the
table top.
WARNING: To reduce the risk of injury, regularly clean the
dust collection system.
Optional Accessories
WARNING: Since accessories, other than those offered by
D
E
WALT, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the
risk of injury, only D
E
WALT, recommended accessories should
be used with this product.
SAW BLADES: ALWAYS USE 305 mm SAW BLADES WITH 30 mm
ARBOUR HOLES. SPEED RATING MUST BE AT LEAST 4000/min. Never
use a smaller or greater diameter blade. It will not be guarded properly.
Use crosscut blades only! Do not use blades designed for ripping,
combination blades or blades with hook angles in excess of 10°.
BLADE DESCRIPTIONS
Application Diameter (mm) Teeth
Construction Saw Blades (for all purpose cutting)
General Purpose 305 36
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts 305 60
Consult your dealer for further information on the appropriate accessories.
Protecting the Environment
Separate collection. This product must not be disposed of with
normal household waste.
E N G L I S H