DeWalt D25810, Оригинальное руководство пользователя

Страница: 20 / 84

18
EngLIsH
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The date code
9
, which also includes the year of manufacture,
is printed into the housing.
Example:
24.10.2018
Year of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
1 Trigger switch
2
Side handle
3 Front Barrel (Collar)
4
Mode selector dial
5 Mode selector release button
6
Main handle
7 Tool holder
8
Sleeve
Intended Use
Your chipping hammer has been designed for professional
chiseling and chipping applications.
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
Your chipping hammer is a professional power tool.
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Active Vibration Control
For best vibration control, hold the tool as described in Proper
Hand Position.
The active vibration control neutralises rebound vibration from
the hammer mechanism. Lowering hand and arm vibration,
it allows more comfortable use for longer periods of time and
extends the life of the unit.
The hammer only needs enough pressure to engage the active
vibraton control. Applying too much pressure will not make the
tool chip faster and active vibration control will not engage.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Side Handle (Fig. A–B)
WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed.
Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold
tool with both hands to maximize control.
The side handle 2 clamps to the front of the gear case and may
be rotated 360˚ to permit right- or left-hand use.
Mounting the Straight Side Handle (Fig. B)
1. Widen the ring opening of the side handle 2 by rotating it
anti-clockwise.
2. Place the assembly onto the chipping hammer putting the
nose of the tool through the steel ring
10
and onto the
collar 3 past the tool holder and sleeve.
3. Rotate the side handle assembly to the desired position.
4. Lock the side handle mounting assembly in place by
securely tightening the handle
2
rotating it clockwise so
that the assembly will not rotate.
Bit and Bit Holder
WARNING: Burn Hazard. ALWAYS wear gloves when
changing bits. Accessible metal parts on the tool and bits
may get extremely hot during operation. Small bits of
broken material may damage bare hands.
WARNING: Do not attempt to tighten or loosen drill bits
(or any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck and
personal injury may occur.
The chipping hammer can be fitted with various chisel bits
depending on the desired application.
Use sharp bits only.
Inserting and Removing SDS-Max Bits (Fig. C)
D25810
nOtE:
Accessories and attachments used must be lubricated
around the SDS fitment before installation.
1. Pull back the locking sleeve 8 and insert the bit shank. The
bit shank must be clean.
2. Turn the bit slightly until the sleeve snaps back into position.