DeWalt D25113-XE Скачать руководство пользователя

Страница: 7 / 12

D25113-XE, D25114-XE

To reverse the rotary hammer, turn it OFF and align the reversing lever (E) with the

yellow arrow pointing backward (viewed when holding drill in operating position).
To position the lever for forward operation, turn the rotary hammer OFF and align the

reversing lever with the yellow arrow pointing forward (viewed when holding drill in

operating position).

D25213-XE, D25313-XE, D25314-XE,

D25315-XE

To reverse the rotary hammer, turn it OFF

and push the reversing lever (E) in so the

yellow arrow pointing backwards shows.
To position the lever for forward operation,

turn the rotary hammer OFF and push

the reversing lever in so the yellow arrow

pointing forward shows.

Mode Selector –

D25113-XE, D25114-XE,

D25213-XE, D25313-XE,

D25314-XE

(Fig. 5)

CAUTION:

Tool must come to a complete

stop before activating the mode actuator

button or damage to the tool may result.

DRILL-ONLY MODE

To use drill-only mode, depress button

(I) and turn the mode selector (G) so the yellow arrow points to the corresponding

symbol as shown. Use drill-only mode for wood, metal, and plastics.

HAMMER/DRILL MODE

To use hammer/drill mode, depress the button and turn the mode selector so the

yellow arrow points to the corresponding symbol as shown. Use this mode for

masonry drilling.

CHISEL ROTATION

To manually rotate the chisel, depress the button and turn the mode selector so the

yellow arrow points to the corresponding symbol as shown.

HAMMER-ONLY MODE

For light chiseling, depress the button and turn the mode selector so the yellow arrow

points to the corresponding symbol as shown.

NOTE:

The yellow arrow on the mode selector must be aligned with the one of the

symbols at all times. There are no operable positions between the positions.

SDS Chuck (Fig. 6)

FIG. 6

D25114-XE,

D25314-XE ONLY

WARNING: Shock Hazard.

To reduce the risk of

serious personal injury, turn tool off and disconnect tool

from power source before making any adjustments or

changing bits.

WARNING:

Burn Hazard.

ALWAYS wear gloves when

changing bits. Accessible metal parts on the tool and

bits may get extremely hot during operation. Small bits

of broken material may damage bare hands.

CAUTION:

Do not use chipping bits in this tool.

Using

chipping bits may cause the tool to bind-up and damage

to the tool may occur.

To insert bit,

insert shank of bit about 19 mm (3/4") into

chuck. Push and rotate bit until it locks in place. The bit

will be securely held.

To release bit,

pull the sleeve (J) back and remove the bit.

OPERATION

Overload Clutch

If the drill bit becomes jammed or caught, the drive to the drill spindle is interrupted.

Because of the forces that occur as a result, always hold the machine securely with

both hands and take a firm stance.

DRILL-ONLY

MODE

CHISEL

ROTATION

HAMMER-ONLY

MODE

FIG. 5

HAMMER/DRILL

MODE

Содержание D25113-XE













Результаты поиска

Содержание D25113-XE

Отзывы:

Похожие инструкции для D25113-XE

Бренды по названию

Популярные бренды

DeWalt D25113-XE, Инструкция по эксплуатации

Результаты поиска

Содержание D25113-XE

Отзывы:

Похожие инструкции для D25113-XE

Бренды по названию

Популярные бренды