background image

8

This warranty gives you specific legal rights and you may have other rights under the 

provisions of the Consumer Guarantee Act 1993 (New Zealand only), Trade Practices 

Act 1974 and State Legislation (Australia only).
In addition to the warranty, D

E

WALT tools are covered by our:

FREE ONE YEAR SERVICE CONTRACT

D

E

WALT will also maintain the tool for free at any time during the first year of 

purchase. This includes labour, parts and lubrication required to restore the product to 

sound mechanical and/or electrical condition. Normal wear parts are not covered in 

this service. Carbon brushes worn more then 50% will be replaced.

NOTE: 

Three Year Warranty is not applicable to items deemed as consumables. Radial 

arm saws are covered by a one (1) year warranty only. D

E

WALT Reserves the right to 

review its warranty policy prior to launch of any new business development products.

30 DAY NO SATISFACTION GUARANTEE

If you are dissatisfied with any D

E

WALT power tool, laser or nailer, for any reason, 

simply return it to the point of purchase with your sales receipt within 30 days for a 

replacement unit or a full refund.

FREE WARNING LABEL REPLACEMENT: 

If your warning labels become illegible or 

are missing, call (AUS) 1800 654 155 or (NZ) 09 579 7600 for a free replacement.

graphic of label goes here.

SPECIFICATIONS

 

D25113-XE, D25114-XE, D25213-XE,  

 D25314-XE, 

D25315-XE 

D25330-XE

Voltage / Frequency: 

230 V ~ 50 Hz 

230 V ~ 50 Hz

Ampere rating: 

800 W 

800 W

RPM: 

0 - 1150 

   –

Beats per minute: 

0 - 4300 

0 - 4300

Содержание D25113-XE













Отзывы: