background image

EN

SB-2-584-H  (4/2016)

7 / 16

INSTALLATION

AIR AND FLUID HOSES

See pages 11, 13, 14 and 15 for installation details.

Use separate filtered regulated air supplies for atomizing and cylinder 

air. Connect all the air and fluid hoses at the back of the manifold (1/8” 

BSP): (See figure) 

•  Cylinder air ‘C = Cyl’ via a control valve. For fast cylinder operation 

the control valve should be fitted as close to the gun as possible or 

an additional quick exhaust valve installed in the line. 

•  Separated atomizing and fan “F” & “A” air supply. 

•  Material hose ‘P’. If material re-circulation is required,  remove the 

plug from port ‘R’ (35) and plug from spray head (34). 

Recommended hose size up to 34 ft. (10 m) long:  

Atomization Air = 0.315 in. (8 mm) 

Cylinder Air = 0.236 in. (6 mm) 

Material = 0.315 in. (8 mm) 

BACK Face of Manifold

TOP Face of Manifold

SETTING

Check that the gun has all of the O-rings installed 

on the sealing surface and check that the locking 

device (28) is in the correct position to lock the 

spray gun on to the connecting plate. 

1.   The  ATOM ‘A’ air valve controls the atomizing air 

pressure. 

2.   The  FAN ‘F’ valve controls the spray pattern size. 
3.  Fluid flow is adjusted with the rear ratchet knob 

(25). 

For the arrangement of the parts, refer to the 

exploded view on page 5. 

START UP 

1.  Turn the needle adjusting knob (25) clockwise 

until the needle is fully closed. 

2.   Turn  the  FAN ‘F’ and ATOM ‘A’ air valves (13) 

counter-clockwise to be full open. 

3.  Use the air cap chart to set the air pressure at the 

air regulator to achieve recommended pressures. 

4.  Turn the adjusting knob (25) counter clockwise to 

obtain the desired fluid flow. 

5.  Test spray. If the finish is too dry or fine, reduce 

the airflow by reducing the air inlet pressure or 

by screwing the valve ATOM ‘A’ (13) in clockwise, 

or increase the fluid flow using ratchet knob, 

rotating counter clockwise.

Important: To ensure that this equipment reaches you in first class condition, 

protective coatings have been used. Flush the equipment through with appropriate 

solvent before use. Fix the spray gun base plate using mounting stem ref.30 and 

secure it with nut ref.29.

Important: The Spray gun must be grounded to dissipate any electrostatic charges 

which may be created by fluid or air flows. This can be achieved through the Spray 

gun mounting, or conductive air/fluid hoses. Electrical bond from the spray gun to 

earth should be checked with an ohmmeter. A resistance of less than 10

6

 Ohms is 

recommended. 

Содержание CMAX-00-0

































Отзывы: