manualshive.com logo in svg

Devair HDI-01, Руководство по установке

Поделиться
Скачать
Devair HDI-01 Скачать руководство пользователя страница 20

A. Excessive Noise

B. Oil Pumping and 

Excessive Carbon 
Formation
or
Appearance of Water 
and Oil in the in the Air 
Lines.

1.  Install a moisture separator and/or oil 

filter in the air line at least 8 feet 
from the air receiver.

2.  Check for air leaks. If no leaks are 

found, you may require an additional 
compressor unit, as your air demand 
is too much for the existing unit.

3.  Clean or replace the piping. Contact 

Devair or contact your local  
Distributor or Service Centre for sizing 
requirements.

4.

Replace air intake filter.

5.

Fill to proper level.

6.

Check 'Lubrication' in this manual or 

contact your local Devair Distributor or 

Service Centre.

7.

Clean or replace as required.

8.

Replace valve assemblies.

9.

Replace rings and check cylinder 

walls for scoring.

1.

High ambient temperature and/or
humidity.

2.  High percentage of running time. (80% 

to 100%)

3.  Obstructed or undersized air intake 

piping, where remote air Intake is 
used.

4.

Restricted air intake filter.

5.

Overfilling the crankcase with oil.

6.

Wrong type of oil.

7.

Carbonned exhaust valves.

8.

Worn valves.

9.

Worn piston rings.

1.  Loose flywheel or motor pulley.
2.  Loose valve.

3.

If noisy only during start-up, check for
loose belts.

4.  Vibrating beltguard, piping, or loose belts.
5.  Unit not installed level.
6.

Improper grade or level of oil in crankcase.

7.  Carbon or other foreign material on head 

of piston.

8.  Normal sound amplified through floor or

carried through remote air intake (when 

used).

9.  If the noise is a knock, and cannot be

attributed to any of the above, the
problem could be worn bearings. 

1.

Tighten as required.

2.  Inspect valve for damage. Replace as

required. Check to ensure valve is 

seated properly in head. Reinstall,

tightening valve plug and set screw

3.  Tighten until no slippage is apparent. 

Allow some slack.

4.  Tighten as required.
5.  Ensure that unit is mounted level.
6.  Use correct oil and ensure level is 

correct.

7.  Clean top of piston. Check cylinder

walls for scoring, etc.

8.  Mount unit on vibration isolators.

Insulate intake piping from building.

9.  Worn main bearings can usually be 

detected by noticeable end play on the 
flywheel. Replace the main bearings.
Worn connecting rod insert bearings 

or connecting rods may be detected by 
removing a valve and watching the 
piston while moving the flywheel by 
hand. If the flywheel can be moved at 
midstroke without movement of the 
piston, bearing inserts or connecting 
rod may need to be replaced.

Suggested Correction  

                                              

 Condition  

                                              

Cause  

                                              

When  servicing  the  Compressor,  shut  off  all  power  to  the  Unit,  and 
drain  the  Tank  of  air  pressure.  Always  replace  the  BeltGuard  after 
adjusting the Belts or Pulleys.

Trouble-Shooting Guide

 - 20 -

HDI-01

Mar ‘07

Distributed by:     CENTRAIR Air Systems & Supplies,    68 Hooper Rd., Unit 5, Barrie, ON  L4N 8Z9

                               Phone: 705-722-5747  Fax: 705-722-5458     [email protected]    www.centrair.ca

Содержание HDI-01

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды