background image

8

SAFETY PROCEDURES

preparaTion

1. Do not allow children to operate this equipment.

2. Do not operate this equipment in the vicinity of bystanders.

3. Do not run the unit in an enclosed area since the exhaust from the engine contains some
 

carbon monoxide, which is a colourless, odourless, tasteless and poisonous gas.

4. Wear safety glasses and hearing protection at all times when operating the machine.

5. Avoid wearing clothing that is loose fitting or has hanging cords or ties.

6. Only operate the machine in open space, not close to a wall or other fixed object, and on a
 

firm, level surface.

7. Do not operate the machine on a paved or gravel surface, where ejected material could
 

cause injury.

8. Before starting the machine, check that all screws, nuts, bolts, and other fasteners are
 

properly secured and that guards and covers are in place. 

9. Replace damaged or unreadable labels. ( See ‘Decals’ section - page 10)

10. Use extra care in handling fuels. They are flammable and the vapours are explosive. The
 

following points should be observed:

• Use only an approved container.
• Never remove the fuel cap or add fuel with the power source running. Allow engine and

  exhaust components to cool before refuelling.

• Do not smoke.
• Never refuel the machine indoors.
• Never store the machine or fuel container inside where there is an open flame, such as

  a gas water heater, pilot or burner.

• If fuel is spilled, do not attempt to start the power source, but move the machine away

  from the area of spillage before starting.

• Always replace and securely tighten the fuel cap after refuelling.
• If the fuel tank is drained, this should be done outdoors.

warninG:

 become familiar with this booklet before starting or operating the chipper.   

Содержание GARDEN CHIPPER 750

























Отзывы: