background image

5

GENERAL DESCRIPTION

The 

Deutscher Garden Chipper 750

 was designed as a garden chipper that is capable of chipping palm fronds and 

similar vegetation, but will also chip green hardwood branches to 65mm diameter, dry hardwood to 25mm diameter 

and dry softwood to 50mm diameter. The chipper can be fitted with a Briggs and Stratton Intek 6.0 or a Honda GX200 

engine. For ease of use, there is only one entry point for material on this machine. One of our primary design aims 

was to produce a machine that self feeds with most materials. This reduces the time taken when chipping and also 

improves operator safety, as it is less likely the operator will need to push material into the hopper. 
The cutting device (rotor) of the Garden Chipper 750 is a 395mm diameter, 8mm thick steel disk with twin tool steel 

chipper blades bolted to its surface. To eliminate the possibility of material wrapping around the drive shaft and 

then causing premature bearing failure, both rotor bearings are mounted behind the disk. The chipper blades are 

reversible to give twice the life, and they can be rotated in the field should they become blunt.

 

A clutch has been fitted to allow easy starting. Also the discharge chute can be locked in the raised position to 

reduce storage space and enable access through gates and shed doors. For your safety, a switch is provided on 

the discharge chute to prevent the machine being started with the chute raised. 

Engine fuel cap

Engine oil fill hole/ 

dipstick under cap

Engine oil drain

Belt guard

Infeed chute

Hopper

Clutch lever

Chipping chamber

Base frame

Discharge chute

Содержание GARDEN CHIPPER 750

























Отзывы: