Detroit Radiant Products QTD2-60N, Руководство по установке, Страница: 5 / 44

!
CLEARANCE TO COMBUSTIBLES (in inches)
FIRE HAZARD. Always maintain published clearance to combustibles.
In locations used for the storage of combustible materials, signs must be
posted. Consult manual for additional guidelines.
DANGER
LLTCL013-2M-09/16 (CDS)
MOUNT LEVEL
Failure to mount appliance level may result in
increased clearances to combustibles.
END VIEW
TOP SIDES BELOW END
SIDE VIEW
This heater must be installed and serviced by trained gas installation and service personnel only.
The installation of this heater must conform with local building codes or, in the absence of such
codes, the National Fuel Gas Code (NFPA 54/ANSI Z223.1).
These applications must comply with:
• Parking Structures, ANSI/NFPA 88A.
• Repair Garages, ANSI/NFPA 30A.
• Aircraft Hangars, ANSI/NFPA 409.
Side Side
Below
Read and understand the installation,
operating and maintenance
instructions thoroughly before
installing or servicing this equipment.
To ensure system performance and safety,
this unit must be properly vented.
A
minimum ventilation rate of 4cfm/1000
BTU/h is required for unvented operation.
This is NOT an explosion-proof heater. Where there is the possibility of exposure to
flammable vapors or dusts, consult the local fire marshal, your insurance carrier or authorities
for approval of the proposed installation. Do
NOT
install in explosive environments.
Gas Hose Gas Pipe
A flexible gas connection of approved
type is required. Flexible stainless steel
gas connectors installed in one plane,
and without sharp bends, kinks or
twists is recommended.
Gas Pipe
Gas Hose
MODEL
BTU/h BACK
60,000 10 36 40 12 6
80,000 10 36 40 12 6
IMPORTANT! Do
NOT exceed 45°
reflector maximum
mounting angle.
End
Top
Below
Back
MOUNT LEVEL
12”
Top
NEUTRAL
EARTH
HOT
- 120V HEATER INPUT -
120V
Right Panel Left Panel
NEUTRAL
EARTH
HOT
- 120V HEATER INPUT -
120V
F/N: LLV3EP1
F/N: LLTCL013: Clearance to
Combustibles and Gas Data Label
F/N: LLLOGO13
Logo Label
F/N: LLV2EP9
Electrical Label
(Located inside service panel)
!
CLEARANCE TO COMBUSTIBLES (in inches)
FIRE HAZARD. Always maintain published clearance to combustibles.
In locations used for the storage of combustible materials, signs must be
posted. Consult manual for additional guidelines.
DANGER
LLTCL013-2M-09/16 (CDS)
MOUNT LEVEL
Failure to mount appliance level may result in
increased clearances to combustibles.
END VIEW TOP SIDES BELOW END
SIDE VIEW
This heater must be installed and serviced by trained gas installation and service personnel only.
The installation of this heater must conform with local building codes or, in the absence of such
codes, the National Fuel Gas Code (NFPA 54/ANSI Z223.1).
These applications must comply with:
• Parking Structures, ANSI/NFPA 88A.
• Repair Garages, ANSI/NFPA 30A.
• Aircraft Hangars, ANSI/NFPA 409.
Side Side
Below
Read and understand the installation,
operating and maintenance
instructions thoroughly before
installing or servicing this equipment.
To ensure system performance and safety,
this unit must be properly vented.
A
minimum ventilation rate of 4cfm/1000
BTU/h is required for unvented operation.
This is NOT an explosion-proof heater. Where there is the possibility of exposure to
flammable vapors or dusts, consult the local fire marshal, your insurance carrier or authorities
for approval of the proposed installation. Do NOT install in explosive environments.
Gas Hose
Gas Pipe
A flexible gas connection of approved
type is required. Flexible stainless steel
gas connectors installed in one plane,
and without sharp bends, kinks or
twists is recommended.
Gas Pipe
Gas Hose
MODEL
BTU/h BACK
60,000 10 36 40 12 6
80,000 10 36 40 12 6
IMPORTANT! Do
NOT exceed 45°
reflector maximum
mounting angle.
End
Top
Below
Back
MOUNT LEVEL
12”
Top
QTD2 Series
5
1.0 Introduction
• Safety Labels and Their Locations
Bill of Materials
(Located inside the service panel)
QTD2-80P
Data on this label is for the model shown on this label. If your heater has been converted,
this information is not accurate. Please contact the factory for assistance.
BURNER COMPONENTS:
For parts replacement information, contact factory at 586-756-0950 or visit www.drp-co.com/parts.
Serial No.: 1611XXXXXXXXXX 0001
Gas Valve:
Circuit Board:
Wire Harness:
N.O. Switch:
N.O. VL Orifice:
N.C. Switch:
N.C. VL Orifice:
Diff Switch:
Diff VL Orifice:
Igniter:
Burner:
16” Tube:
Ind. Lights: Diag. Light:
Term. Block:
Transformer:
Fan:
Alt. Fan:
Alt. Fan Usage:
Relay:
Filter:
24 Volt In:
120 Volt In:
Gas In:
Extra VL Orifice:
Production Code:
Version:
Stock:
Add-On:
Internal Use Only:
HEATER
TYPE:
Electric:
Tag: Special 1:
Special 2: Gas:
Air:
C1
C1 C2 C3
None
N/A
QTD2
01.16
Two-Stage
Ignition Control
3 PCS Harness
None
None
None
None
IS22016051F5169
Grey (+ / -)
Norton
High
4” Gen.
Yellow - 120V
(Specify TP-#’s)
3140
851B
3252
N/A
N/A
264E
50
201B
1080
828
None
None
None
Fasco Lg.
50Hz - 120V
When Specified
None
None
None
120V Cord
7/8” FC Flare
None
N/A
N/A
55A
55B
N/A
N/A
334
333
83
3
1 1/2”
TP-204#
TP-44# 3
1 5/8”
LLWT603
None 1
1 5/8”
17
1 7/16”
Orifice Type:
SA
MP
LE