Detroit Radiant Products EDX Series Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 44

Detroit Radiant Products EDX Series Скачать руководство пользователя страница 1

EDX Series

Installation, Operation,

Maintenance, and Parts Manual

LIOEDXc-Rev. 08617

Print: 1c-12/20 (DRPC)

Replaces: 1c-03/19 (DRPC)

WARNING

!

CE Certified 230V-50Hz. (G20, G25, G25.3, and G31) Infrared Tube Heater.

The EDX Series Infrared Tube Heater is a positive pressure, single stage radiant heater system. All persons
involved with the installation, operation, and maintenance of the heater system must read and understand the
information in this manual.

For Your Safety

If you smell gas:

• Do not try to light any appliance.

• Immediately call your gas supplier from a neighbor’s phone.

• Do not touch any electrical switch.

• Follow the gas supplier’s instructions.

• Do not use any phone in your building. • If you cannot reach your gas supplier, call the fire department.

INSTALLER: Present this manual to the end user.

Keep these instructions in a clean and dry place for future reference.

Model#:

___________________

Serial #:

_________________________

(located on rating label)

Improper installation, adjustment, alteration, service, or maintenance can cause
property damage, injury, or death. Read the installation, operation, and maintenance
instructions thoroughly before installing or servicing this equipment.

This heater

must

be installed and serviced by a Gas Safe Registered Gas Engineer

only! Conversion of the heater for use with other gases must be carried out by a Gas
Safe Registered Gas Engineer. Failure to comply could result in personal injury,
asphyxiation, death, fire, and/or property damage.

In locations used for the storage of combustible materials, signs must be posted to
specify the maximum permissible stacking height to maintain the required clearances
from the heater to the combustibles. Signs must either be posted adjacent to the
heater thermostats or, in the absence of such thermostats, in a conspicuous location.

0063

1
2
3
...
»

Содержание EDX Series













































Отзывы:

Нет отзывов