OPERATIONS
SPECIAL NOTES and DEFINITIONS:
1. The door needs to be closed to test the unit.
2. When operating the ON/OFF switch, there is a slight delay.
3. The key is inserted and removed only in the vertical position (home position).
4. Key function: counter clockwise (CCW) = Armed; clockwise (CW) = Disarmed
5. The door prop function is selectable by setting SWITCH A to the OFF position.
For door chime function, set SWITCH A to the ON position
MAGNET HANDING PROCEDURE:
Magnet handing is where the device determines if the left,
right or an external reed switch will be used to indicate if the door is opened or closed. When the
battery is initially installed, the device simultaneously flashes the LEDs and chirps the siren a total
of five times. This indicates that the device is in the magnet handing process:
Step 1: If re-handing is necessary, remove the unit from the door, momentarily short the
REHANDING (or
Test)
jumper contacts. The device simultaneously flashes the LEDs and
chirps the siren a total of five times.
Step 2: Turn the key CW to the 'OFF' position.
Step 3: Install the device on the door.
Step 4: With the door open, turn the key CCW to the 'ON' position. The red LED blinks twice.
Step 5: Close the door and bring the external magnet into position with the external door switch.
The siren chirps and the LED flashes on the selected side of the device (red LED flashes for
the left side or external; green LED flashes for right side).
The device will now operate normally, and the selected reed switch side is stored in memory so
changing the battery does not require re-handing.
DOOR PROP OPERATIONS:
The door prop function is selected by setting SWITCH A to the 'OFF'
position. To arm the system, close the door and turn the key CCW to the 'ON'
position. The red LED will flash twice indicating that the device is now armed. If the door is opened,
the device will begin a timing countdown according to the selected amount of time (15 seconds default).
If the
Status Indicator
(switch B) is 'ON', the red LED will blink every second during the countdown. If the door is not closed
before the door prop time runs out, the alarm sounds and the red LED flashes. Closing the door will silence the alarm and
rearm the unit. To change the door prop timing, see the section
Changing Door Prop Timing
.
DOOR CHIME OPERATIONS:
The door chime function is selected by setting SWITCH A to the 'ON' position.
To arm the system, close the door and turn the key CCW to the 'ON' position. The red LED will flash twice indicating
that the device is now armed. If the door is opened, the device sounds a series of siren chirps lasting
five seconds. No other action is taken until the door is closed and the unit rearms.
DISARMING:
To turn off the alarm or disarm the system, turn the key CW to the 2 o'clock position.
TROUBLESHOOTING: If the unit does not arm, the magnet may need to be re-aligned or shimmed closer to
the EAX-300. If the unit fails to operate correctly, restart the device by removing the battery for approximately
five seconds.
LOW BATTERY ALERT:
Simultaneous siren chirps and red LED flashes occur at 45 second intervals when
battery reaches approximately 7 volts. The
LV Opt
jumper must be in place to use this feature (default).
STATUS INDICATOR:
With the Status indicator (SWITCH B) 'ON': red LED flashes every six seconds
when armed; green LED flashes every six seconds when disarmed.
"ON"
position
"OFF"
position
"ON"
position
Key orientation
without
Key Stop
installed
Key orientation
with
Key Stop
installed
"OFF"
position
ON
OFF
ON
OFF
ON
OFF
ON
OFF
REHANDING
(or
Test)
jumper
contacts.
LV Opt jumper
behind cover
(under SWITCH A)
104889 Page 6
