Detecto WPB Series Скачать руководство пользователя страница 16

Страница: 16 / 24

8525-0380-0M Rev B

WPB Series Owner’s Manual

CHECK WEIGHING, CONT.

(LiM-BZ) – Enable or Disable Check Weighing Beeper

With the display showing

(LiM-BZ, press the

key.

The display will change to show the current setting.

If the current setting is acceptable, press the

key to save it and return to the

weight display.

If the current setting is not acceptable, press the

key to toggle the selection and

then press the

key to save it and return to the weight display.

Allowable settings for the check weighing beeper are:

(LiM-BZ)

The beeper is enabled.

(LiM-MU)

The beeper is disabled (muted).

CHECK WEIGHING OPERATION

Check Weighing must be enabled before operations can begin. Perform the following to
enable check weighing:

If the scale is not on, press the

ቄ

key to turn it on.

If the scale is on, skip to step 3

The scale will perform a display test and then change to the weight display.

Press the

࿎

key to enable check weighing.

The scale display will momentarily show

C6- on

(CHECKING ON), to indicate the

check weighing function has been enabled.

NOTE: The functions of the LEDs and beeper are selected when setting the
Upper and Lower limits. Refer to the

set-Li

(SET Li) – Set the Check

Weighing Functions setting.

Items that are outside the weight range, (over or under) are identified by turning on an LED,

(for over) or

(for under) and if enabled, sounding the beeper. Items that are within the

weight range (between the lower limit and upper limit settings) are identified by turning on the

(for acceptable) LED and if enabled, sounding the beeper.

Weight is Greater than Upper (Hi) Limit Setting

(LiM-Hi) was selected, the

LED is turned on, and the scale will beep (until the

weight is removed), to signal that the weight is greater than the Upper Limit weight setting.

Weight is Less than Lower (Lo) Limit Setting

@!6

(LiM-Lo) was selected, the

LED is turned on, and the scale will beep (until the

weight is removed), to signal that the weight is less than the Lower Limit weight setting.

Weight is Acceptable (Ok) Limits

(between lower limit and upper limit settings)

@-0

(LiM-in) was selected, the

LED will turn on, and the scale will beep (until the

weight is removed), to signal that the weight is within the acceptable limits (greater than the
lower limit setting and less than the upper limit setting).

Содержание WPB Series

























Результаты поиска

Содержание WPB Series

Отзывы:

Бренды по названию

Популярные бренды

Detecto WPB Series, Руководство пользователя

Результаты поиска

Содержание WPB Series

Отзывы:

Бренды по названию

Популярные бренды