background image

TB-6601

 Page 7 of 7

© 2019 DESCO INDUSTRIES INC

Employee Owned

DESCO WEST 

- 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST 

- One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: 

Desco.com

Calibration

Frequency of recalibration should be based on the 

critical nature of those ESD sensitive items handled 

and the risk of failure for the ESD protective equipment 

and materials. In general, Desco recommends that 

calibration be performed annually.
Use the EMIT 50424

 

Limit Comparator and EMIT 50784 

5-Pound Electrode to perform periodic verification (once 

every 6-12 months) of the Combo Tester X3+. The Limit 

Comparator can be used to check the test limits of the 

Combo Tester X3+ without removing it from the factory 

floor.
See 

TB-6581

 for more information.

NOTE: Calibration is not required for the temperature 

and humidity sensor embedded within the Combo 

Tester X3+.

Specifications

Combo Tester

 X3+

Input Voltage and 

Frequency

(External Adapter)

AC/DC Power Adapter
Power Input: 

100-240VAC, 50/60 Hz
Power Output: 

5VDC, 3.0A
Cable Length: 

5 ft. (1.5 m)

Operating Temperature 70°F to 85°F (21°C to 30°C) 

for 1 gigohm test limit
41°F to 85°F (5°C to 30°C) 

for all other test limits

Environmental 

Requirements

Indoor use only at altitudes 

less than 6500 ft. (2 km)
Maximum relative humidity 

of 80% up to 85°F (30°C) 

decreasing linearly to 50% @ 

85°F (30°C)
Maximum relative humidity of 

50% at 1 gigohm setting

Dimensions

6.75" x 5.00" x 1.75"

(17.1 cm x 12.7 cm x 4.4 cm)

Weight

1.8 lbs (0.8 kg)

Test Accuracy

±20% for 1 gigohm footwear 

test limit
±10% for all other test limits

Test Switch Voltage

5 VDC @ open circuit

Wrist Strap and 

Footwear Test Voltage

30 VDC @ open circuit
Test current is limited by 

resistors and varies on 

the test range setting (100 

kilohms - 1 gigohm)

Temperature Accuracy ±0.5°C 
Humidity Accuracy

±5%

Dual Independent Foot Plate

Dimensions

13.25" x 15.25" x 1.125"

(337 mm x 387 mm x 29 mm)

Weight

5.5 lbs (2.5 kg)

Figure 13. EMIT 50424 Limit Comparator

Figure 14. EMIT 50784 5-Pound Electrode for Limit 

Comparator

Limited Warranty, Warranty Exclusions, Limit 

of Liability and RMA Request Instructions

See the Desco Warranty - 

Desco.com/Limited-Warranty.aspx

Содержание Combo Tester X3+








Отзывы: