www.desatech.com
118116-01D
4
FIREPLACE INSTALLATION
6HW¿UHSODFHGLUHFWO\LQIURQWRIWKLVRSHQ
-
LQJDQGVOLGHXQLWEDFNXQWLOQDLOLQJÀDQJHV
touch the side framing.
&KHFNWKHOHYHORI¿UHSODFHDQGVKLPZLWK
sheet metal if necessary.
5. Before securing fireplace to prepared
framing, ember protector (provided) must
be placed between hearth extension (not
supplied) and under bottom front edge
RI ¿UHSODFH WR SURWHFW DJDLQVW JORZLQJ
HPEHUV IDOOLQJ WKURXJK ,I ¿UHSODFH LV WR
be installed on a raised platform, a Z-type
ember protector (not supplied) must be
IDEULFDWHG WR ¿W \RXU UHTXLUHG SODWIRUP
height. The ember protector should ex-
WHQGXQGHU¿UHSODFHDPLQLPXPRI
1
/
2
".
The ember protector should be made of
JDOYDQL]HGVKHHWPHWDOJDXJHPLQL
-
mum to prevent corrosion.
8VLQJVFUHZVRUQDLOVVHFXUH¿UHSODFHWR
IUDPLQJWKURXJKÀDQJHVORFDWHGRQVLGHV
RI¿UHSODFH
60.875"
65.7"
71.5"
76.25"*
31.625"
Secure Fireplace
To Hearth Spacer
Using Straps Provided
(Sides and Rear)
Figure 1 - Framing Dimensions
Figure 2 - Corner Installation
107.3"
78.875
"
Maintain 1
1
/
2
"
Clearance at Sides and
Back of Fireplace
1
1
/
2
" Clearance
Not Required at
Nailing Flanges
SELECTING LOCATION
7R GHWHUPLQH WKH VDIHVW DQG PRVW HI¿FLHQW
ORFDWLRQIRUWKH¿UHSODFH\RXPXVWWDNHLQWR
consideration the following guidelines:
1. The location must allow for proper clear-
ances (see Figures 1 and 2).
&RQVLGHU D ORFDWLRQ ZKHUH WKH ¿UHSODFH
will not be affected by drafts, air condition-
ing ducts, windows or doors.
3. A location that avoids the cutting of
joists or roof rafters will make installation
easier.
4. An outside air kit is available with this
¿UHSODFHVHH
Optional Outside Air Kit
on
page 6).
MINIMUM CLEARANCE TO
COMBUSTIBLES
%DFNDQGVLGHVRI¿UHSODFH
1
/
2
" min.*
)URQWRI¿UHSODFH
PLQ
Floor**
0" min.
Perpendicular wall to opening 18" min.
Top spacers
0" min.
Mantel clearance
see
Mantels
, page 5
Chimney outer pipe surface 2" min.
1RWUHTXLUHGDWQDLOLQJÀDQJHV
** See step 2 of
Framing
WARNING: Do not pack re-
quired air spaces with insulation
or other materials.
0LQLPXP0D[LPXP&KLPQH\+HLJKW
The minimum height of the chimney, mea-
VXUHG IURP WKH EDVH RI WKH ¿UHSODFH WR WKH
ÀXHJDVRXWOHWRIWKHWHUPLQDWLRQLVIHHWIRU
VWUDLJKWÀXHRUDÀXHZLWKRQHHOERZVHW7KH
maximum distance between elbows is 6 feet.
For systems with two elbow sets, the minimum
height is 22 feet. The maximum height of any
system is 50 feet. This measurement includes
WKH¿UHSODFHFKLPQH\VHFWLRQVDQGWKHKHLJKW
of the termination assembly at the level of the
ÀXHJDVRXWOHWVHH)LJXUHSDJH
FRAMING
)UDPHWKHRSHQLQJIRUWKH¿UHSODFHXVLQJ
the dimensions shown in Figures 1 and 2.
,IWKH¿UHSODFHLVWREHLQVWDOOHGGLUHFWO\RQ
carpeting, tile or any combustible material
LQFOXGLQJZRRGÀRRULQJWKH¿UHSODFHPXVW
be installed on a hearth spacer designed
IRUXVHZLWKWKLV¿UHSODFHVHH
Replace-
ment and Accessory Parts
, page 18).