background image

105501-01F

For more information, visit www.desatech.com

For more information, visit www.desatech.com

23

23

 WARNING: The glass door must be securely in

place before running this burner system. Do not run
this burner system if glass is missing or broken.

STOVE AND DIRECT-VENT
BURNER SYSTEM
INSTALLATION

Continued

STOVE AND DIRECT-VENT BURNER SYSTEM INSTALLATION

Installing Logs, Lava Rock, and Glowing Embers (Cont.)

OPERATING STOVE WITH BURNER SYSTEM

For Your Safety Read Before Lighting

LIghting Instructions

7.

Pull ember material apart into pieces no larger than a dime.
Place these pieces loosely and sparingly directly  onto the ex-
posed section of the front burner and along the space between
the burner and grate prongs (see Figure 55). This will create
the glowing ember appearance as the flame touches the ember
material. Do not block air slots by using too much ember ma-
terial in one area. It is not necessary to use all of the ember
material provided.

8.

Replace the glass door and stove front. See Removing/Replac-
ing Glass Door
, page 21.

Figure 55 - Placing Ember Material on Burner

OPERATING STOVE WITH
BURNER SYSTEM

1.

STOP! Read the safety information above.

2.

Open lower panel.

3.

Turn ON/OFF switch to “OFF”.

4.

Turn off all electric power to the burner system.

5.

Push in gas control knob slightly and turn clockwise

 to “OFF”.

6.

Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information above. If you don't smell
gas, go to the next step.

7.

The pilot is located by the main burner and should not
require accessing for lighting.

8.

Turn gas control knob counterclockwise 

 to “PILOT”.

 WARNING: If you do not follow these instructions

exactly, a fire or explosion may result causing prop-
erty damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand.

When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area

for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone

in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by hand,
don't try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.

FOR YOUR SAFETY

READ BEFORE LIGHTING

LIGHTING

INSTRUCTIONS

Содержание CDVBNC









































Отзывы: