111244-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
23
23
OPERATING FIREPLACE
Continued
OPERATING FIREPLACE (REMOTE-READY MODELS)
Optional Hand-Held Remote Operation (Cont.)
Optional GWMT1 Wall Mounted Thermostat
Optional GWMS2 Wall Mounted Switch
Operating Blower
Figure 44 - Thermostat Hand-Held Remote Control Unit
([C]GHRCTB)
Turns Hand-Held
Remote On or Off
and Allows You to
Choose the
Manual Setting
Selects Auto
Setting
Increases Room
Temperature in
AUTO Mode
Locks System to
Prevent
Accidental Ignition
Digital Display
Shows
Temperature and
Settings
Turns Burners
On or Off
Decreases Room
Temperature in
AUTO Mode
Note:
Do not leave the hand-held remote in the AUTO mode
close to the fireplace. The radiant heat from the fireplace will
turn off the fireplace. Ideally, place the hand-held remote in the
center of the room facing towards the fireplace.
Note:
Do not hold the hand-held remote for a long time. Body
temperature will affect its operation in the AUTO mode.
Safety Features
When away from home for an extended period of time or as a
child safety feature to prevent accidental ignition of the fire-
place, the receiver ON/OFF/REMOTE switch should be in the
OFF position.
Auto Shutoff Feature
1.
If the average room temperature exceeds 82 degrees Fahr-
enheit (28 degrees Centigrade), the hand-held remote con-
trol will perform a safety override and shut the fireplace
off. This feature is not available in the MANU mode.
2.
The receiver continuously receives signals from the hand-
held remote to control the room temperature. If the hand-
held remote is misplaced, obstructed, or for any reason can-
not transmit to the receiver, the receiver will shut off the
fireplace after 8 minutes.
Key Pad Lock Feature
This feature allows the user to lock/unlock the keypad on the hand-
held remote in the MANU or AUTO mode to prevent inadvertent
operation (i.e. children operating the hand-held remote control,
etc.). The keypad is locked in either on or off. Press the POWER
and LOCK buttons together to turn the unit on or off.
Make sure the heater switch is on AUTO. This wall switch works
just like the conventional light switch. Flip the switch up for on
and down for off.
Note:
Make sure that this switch is not in a position to be
mistaken for a light switch. This may result in the fireplace being
inadvertently turned on without the proper precautions being
taken. See installation instructions on page 18.
OPERATING
BLOWER
AUTO/OFF/ON Switch
This blower has three settings: ON, OFF, and AUTO. In the ON
position, the blower will operate constantly. In the OFF posi-
tion, the blower will not operate. In the AUTO position, the
blower will start when the thermostat senses a sufficient in-
crease in firebox temperature.
Note:
Your fireplace and thermostat blower will not turn on
and off at the same time. The fireplace may run for several
minutes before the blower turns on. After the heater modulates
to the pilot position, the blower will continue to run. The blower
will shut off after the firebox temperature decreases.
Note:
It is safe to operate fireplace with blower turned off.
However, the blower helps distribute heated air from the fireplace.
Figure 45 - AUTO/OFF/ON Blower Switch
OPTIONAL GWMS2 WALL
MOUNTED SWITCH
OPTIONAL GWMT1 WALL
MOUNTED THERMOSTAT
Make sure the heater switch is on AUTO and set the temperature
adjustment on wall thermostat to the desired setting. The ther-
mostat has been electronically calibrated at the factory and
requires no adjustment or leveling.
Upon installation, the thermostat must be allowed to stabilize at
room temperature for a minimum of 30 minutes for proper
operation. See installation instructions on page 18.
