Denon AVR-X4100, Руководство по обслуживанию

Страница: 18 / 236

SPECIAL MODE
Special Mode Configuration Buttons
b
No. 1 - 12, 15 : Hold down buttons" A ", " B " and " C " at the same time and press the power button to turn on the power.
b No. 13, 14 : Hold down buttons "
A
" and "
B
" for at least 3 seconds while the power is on.
b
No. 16 ： Press the "
A
" and "
B
" buttons simultaneously while inserting the AC plug to turn the power on.
No. Mode ButtonnA ButtonnB ButtonnC Contents
1
Version Display
(u-COM / DSP Error Display)
SETUP OPTION -
Displays the version of firmware such as the main firmware or DSP,
etc. Errors that have occurred are displayed.
(See 19 page )
2
User Initialization Mode
(Settings for the Installer Setup are not
initialized.)
BACK INFO -
Initializes backup data.
(Settings for the Installer Setup are not initialized.)
3
Factory Initialization Mode
(Initialization includes settings for the
Installer Setup.)
CURSOR
d
CURSOR
f
-
Initializes backup data.
(Initialization includes settings for the Installer Setup.)
4 PANEL / REMOTE LOCK Selection Mode STATUS INFO -
Start this unit in the PANEL/REMOTE LOCK selection mode so that
PANEL LOCK and Remote Lock can be selected as ON or OFF.
(See 23 page )
5
Check the Video/Audio pass
Mode
STATUS
ZONE3
SOURCE
-
This is a special mode for service confirmation used during repair
work to simplify the confirmation work for the Audio channel/vid-
eo channel. (See 27 page )
6
Protection History Display Mode ↑ ↑ -
Displays the protection occurrence history.
(See 71 page )
7
232C Standby Clear Mode : ↑ ↑ -
Switches from 232C standby mode to normal standby mode.
(See 72 page )
8
Operation Info Mode ↑ ↑ -
Displays the total operating time of the set, number of times the
power was switched on, and number of occurrences of each pro-
tection.(See 73 page )
9
TUNER STEP mode
(E3 and E2 model only)
↑ ↑ -
Enables reception STEP of the ANALOG TUNER to be changed.
(See 74 page )
10
Remote ID Setup Mode ↑ ↑ -
If there are multiple DENON AV receivers in the same area, this
mode stops the other AV receivers from being operated concur-
rently with this device. (See 75 page )
11
Installer Setup Mode
CURSOR
0
BACK -
Access the Remote Maintenance mode via the internet. Installer
Setup is displayed on Setup menu / Network.
b
Refer to AVR_RemoteMaintenance_.pdf of SDI.
12
Protection Pass Mode
CURSOR
0
STATUS
ZONE3
SOURCE
Enables the power to be turned on when protection detection is in
the stopped state.
(See 76 page )
13
CX870 / CY920 Reboot mode DIMMER SETUP - CX870 / CY920 をリセット (See 76 page )
14
CX870 / CY920 Initialization mode DIMMER
CURSOR
1
-
Enter this mode only after replacing Flash for CX870 / CY920 and
rewriting the firmware.
(See 77 page )
15
USB Update Mode STATUS OPTION
Switches this unit to USB Update mode.
(See 81 page )
16
Forced USB All Device Write Mode STATUS OPTION -
Mode used when this unit cannot be recovered.
Forcibly switches this unit to USB update mode.
(See 83 page )
NOTE:
When the volume indicator displays " ", the set has entered a special mode for developers.
In this case, RS-232C communication cannot be used.
To cancel this special mode, press and hold the " CURSOR
f
"and " STATUS " buttons for 3 seconds and longer. When the volume indica-
tor returns to the normal display, RS-232C communication can be used.
X
ZONE3
SOURCE
d
0 1
STATUS DIMMER
INFO OPTION
SETUP BACK
f
18