Delta Unifence 36-905 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 20

Delta Unifence 36-905 Скачать руководство пользователя страница 6

6

Fig. 11

Fig. 12

Fig. 14

Fig. 13

Fig. 15

F

K

H

M

L

ASSEMBLING
UNIFENCE TA B L E
TO SAW

1.

Remove #14 x 3/4 inch-long screw (E) Fig. 12, which

was installed in STEP 5, page 4.

2.

Assemble Unifence table (A) Fig. 11, to brackets (B)

using two #14 x 3/4 inch-long screws (D) and screw (E)

which was removed in STEP 1, Fig. 12. NOTE: The two

screws (D) Fig. 12, can be tightened; screw (E) should

be left slightly loose at this time. CAUTION: Overtight-

ening screws in particle board may cause them to strip.

3.

Using a straight edge (F) Fig. 13, make certain the

Unifence table surface is level with the saw table by

adjusting two leveling screws on bottom of table legs and

adjusting brackets (B) Fig. 14. Then tighten three nuts

(C) Fig. 14. IMPORTA N T:

Front edge of Unifence table

must be flush with or slightly behind front edge of saw

table.

4.

Place the shelf support (H) Fig. 15, against table legs

and fasten with U-bolts (K), flat washers (L), and hex

nuts (M) as shown.

«
...
4
5
6
7
8
...
»

Содержание Unifence 36-905





















Отзывы:

Нет отзывов